Porter Cable PCC660 Manuel D'instructions page 6

Scie circulaire de lithium-ion de 20 v max.*, 165 mm (6 1/2 po)
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

masonry products, and arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
WARNING:
cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body. Always operate tool in well-ventilated area and provide for
proper dust removal. Use dust collection system wherever possible.
Symbols
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V ..................volts
Hz ................hertz
min ..............minutes
or DC ..direct current
................Class I Construction
(grounded)
................Class II Construction
(double insulated)
............Read instruction manual before use
................Use proper eye protection
to Reduce tHe RISk of kIckBAck
• Keep a firm grip on saw with both hands at all times.
• Stay alert – exercise control.
• Support long overhanging materials. As the material is cut and weakens, it will sag,
causing a pinched blade.
• Support large panels as shown (fig. e). Material supported only at the ends (fig. d)
will lead to blade pinching.
• Avoid sawing overhead. Material can sag and will pinch blade.
• Insure that the material to be cut is clamped (figure G) and solidly supported and
balanced on a strong, stable and level work surface. Support the work so that the
wide portion of the saw shoe is on the portion of the material that doesn't fall after the
cut is made. Never hold cut off piece by hand (figure f)
• Keep blades sharp and clean.
• Use fence or straight edge guide when ripping. Be careful as the cut off strip can sag
or twist, closing the cut and pinching the blade, leading to KICKBACK.
• Don't force tool. Wood variables such as knots, hardness, toughness, wetness,
pressure treated and freshly cut green lumber can heavily load the saw which can
lead to stalling. Push the saw slower when this occurs.
• Don't remove saw from work during a cut while the blade is moving.
• Allow saw to reach full speed before blade contacts material to be cut. Starting the
saw with the blade against the work or pushed forward into cut can lead to stalling or
sudden backward movement of saw.
• Never attempt to lift saw when making a bevel cut. This leads to blade binding and stalling.
• Always secure work to prevent workpiece movement during cut.
• Do not try to force saw back on line if your cut begins to go off line. This can cause
KICKBACK. Stop saw and allow blade to coast down to a stop. Withdraw from cut
and start a new cut on the line.
• Set depth adjustment of saw such that one tooth of the blade projects below the
workpiece as shown in (figure I).
• Do not back up a rotating blade in the cut. Twisting the saw can cause the back edge of the
blade to dig into the material, climb out of the work and run back toward the operator.
• Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.
Use of this tool can generate and/or disburse dust, which may
A ...................amperes
W ..................watts
or AC......alternating current
n o .................no load speed
..................earthing terminal
................safety alert symbol
.../min or rpm...revolutions or
reciprocation per minute
..................Use proper respiratory protection
..................Use proper hearing protection
6

Publicité

Table des Matières
loading

Table des Matières