Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
This instruction provides for the installation of a Statement or Minimalist
handle collection on a 3/4" standard or flush inset custom panel.
DRILL PILOT HOLES
•
Measure, mark and draw a line 1-1/4" (3.18 cm) from
the handle side edge, top to bottom.
•
Please refer to Table 1 in page 1 for1/2" (1.27cm) hole
center to center distance (L)
•
Center punch to mark hole locations.
•
Drill 1/2" (1.27cm) pilot holes from the appearance side
and through the entire panel thickness.
•
Drill 11/32" (0.87cm) pilot holes from the appearance
side and through the entire panel thickness. (On
vertical handle panels, drill hole 0.720" (1.83cm) below
the 1/2" (1.27cm) hole on top side of the door panel
and 0.720" (1.83cm) above the 1/2" (1.27cm) hole on
1-1/4"
bottom side of the door panel. On Horizontal handle
panels, drill hole 0.720" (1.83cm) towards the center of
the door from 1/2" (1.27cm) hole.)
3"
•
Use a 1" (2.54cm) router bit to route 1/4" (0.64 cm)
(7.62cm)
deep on a 3/4" (1.91 cm) panel. See illustration.
NOTE: The routing counter bore in the rear of the
11/32"
decorative panel must ensure 1/2" (1.27 cm) material
thickness remains for handle support.
1/2"
(1.27cm)
HANDLE ASSEMBLY
11/32"
• Insert stud assembly E from the nonappearance side of
the panel
.720"
• Place the handle caps over the insert stud on the door.
3"
Take care to support the handle so it doesn't fall and
(7.62cm)
scratch the appliance finish. Make sure both handle
caps are resting on the face of the door.
1/2"
• Lock one end of the handle into position by tightening
the countersunk screw D with the Allen wrench
provided. DO NOT over-tighten.
• Keep supporting the handle as you lock the other end
of the handle into position by tightening the countersunk
screw D. DO NOT over-tighten.
• Finally tighten the set screw in the handle caps using
the Allen wrench provided in the handle kit
NOTE: Set screw location
in end cap will vary by
model.
When installing horizontal
handles, position the
handle so that the set
screws are facing
downward.
with handle kit
Installation Instructions
1/4"
(0.64cm)
(1.91cm)
3/4"
Insert Assembly E
D
Allen wrench
2
provided in
the kit
View from
Nonappearance side
(3.18cm)
(2.54cm)
(2.54cm)
1-1/4"
(3.18cm)
Tighten the set screw in the
handle cap after tightening
screw D
Allen Key provided
D
with handle kit
Allen wrench
provided in
the kit
1-1/4"
(3.18cm)
1/2"
1-1/4"
(1.27cm)
3"
(7.62cm)
.720"
(1.83cm)
11/32"
1"
(0.87cm)
Detail Top Side
1"
11/32"
(0.87cm)
.720"
(1.83cm)
3"
(7.62cm)
1/2"
(1.27cm)
1-1/4"
(3.18cm)
Detail Bottom Side
Allen Key provided
with handle kit
31-1000561 Rev. 0
1/2"
(1.27cm)
Publicité
Table des Matières
