Important User Information - Peltor MT7H79 Serie Mode D'emploi

EN
Peltor MT7H79* headset
YOU'VE MADE AN EXCELLENT CHOICE!
Peltor headsets are tested and approved in accordance with PPE
directive 89/686/EEC, so they meet the demands for CE labelling.
Read these instructions carefully to gain the most benefit from
your Peltor product.
A) HEADSET
Qualities
1a. Extra broad headband (MT7H79A) with soft padding for
ideal comfort throughout the working day.
1b. Collapsible headband (MT7H79F) for convenient storage
when you are not using the headset.
1c. Neckband (MT7H79B) for situations where the headband
must not be in the way.
1d. Helmet attachment (MT7H79P3E) allows the headset to be
worn with all common helmets.
2. Individually sprung headband wires of stainless sprung steel
provide an even distribution of pressure around the ears.
Steel headband wires retain their resilience better than
plastic through a wide temperature range.
3. Low, two-point fasteners and easy height adjustment with
no protruding parts.
4. Soft, wide foam and fluid-filled sealing rings with built-in
pressure-evening channels provide low pressure, effective
sealing and ideal comfort.
5. Earphones that provide excellent sound reproduction even in
noisy environments.
6. Connection cord, insulated with flexible polyurethane and
with a moulded connector.
7. Dynamic microphone with high noise suppression. Easy to
replace with a connector.
STANDARD MODELS
MT7H79* headset with 230-ohm earphones and 0.5–1.4-m
connector cable of soft, spiral polyurethane with moulded Nexus
TP-120 connector. Weight without connector cord: MT7H79A 315
g, MT7H79B 300 g, MT7H79P3E 345 g.
MT7H79*-50 EEX-approved headset with 230-ohm earphones
and 0.5–1.4-m connector cable of soft, spiral polyurethane with
moulded Nexus TP-120 connector. Weight without connector
cord: MT7H79B-50 300 g, MT7H79F-50 335 g, MT7H79P3E-50
345 g.
NOTE
Special regulations for safe usage
The Ex certificate (EC-Type Examination Certificate: Nemko
02ATEX059X) contains restrictions about electronic data for con-
nected equipment.
MT7 MICROPHONE
Type: Dynamic differential microphone
Frequency range: 70–9000 Hz +/- 6 dB
Sensitivity as lip mike: 4 mV/220 Ω
Impedance: 230 Ω
Noise suppression: 12 dB at 1 kHz
C) INSTALLATION/SETTINGS
Headband A and F (Fig. C)
(C:1) Slide out the cups. Place the headset over your ears so that
the sealing rings fit snugly.
(C:2) Adjust the height of the cups to a snug, comfortable fit by
sliding the cup up or down while holding the headband flat on
your head.
(C:3) The headband should go straight over the top of the head.
Neckband B (fig. D)
(D:1) Adjust the cups so that the ears are completely surrounded
by the ear cushions.
(D:2) Adjust the height using the headband until you have a snug,
comfortable fit.
(D:3) The headband should lie across the top of the head.
Helmet attachment P3E, P3G and P3K. (Fig. E)
(E:1) Snap the helmet attachment into the slot on the helmet.
Note: The cups can be set in three positions: Working position (E:2),
ventilation position (E:3) and parking position (E:4).
When in use, the cups must be placed in working position. Press
the wires inward until you hear a click on both sides. Make sure
that the cup and the headband wire in working position are not
pressing on the helmet lining or the edge of your hardhat so that
leakage can occur. Parking position should not be used if the cups
are damp inside after an intense period of use.
Peltor's hearing protectors fit most safety helmets in the mar-
ket
Peltor's hearing protectors fit most safety helmets available in the
market today. The hearing protector is adapted to a specific helmet
by a simple manipulation. Peltor's hearing protector for helmets is
fitted as standard with snap-mount Z3E, which can be replaced with
the Z3G or Z3K mount enclosed loose in each carton.
Z3E: Is fitted on delivery and suits Peltor's G22 type helmet and
most other safety helmets available in the market.
Z3G: Suits Peltor's G2000 type helmet with 6-point mount and
also Erin, Protector HC 71, Protector Style, Protector Tuffmaster
II and III etc.
Z3K: Suits Peltor's G2000 safety helmet.
Replacing snap-mount Z3E with Z3G or Z3K
You will need a screwdriver for recessed head screws to change
the snap-mount on your hearing protector.
(E:5) Unscrew the middle screw holding the Z3E snap-mount.
(E:6) Replace the snap-mount with Z3G or Z3K depending on which
type of safety helmet is being used. NOTE. Ensure the snap-mount
is turned the right way round.
(E:7) Tighten the middle screw again.

IMPORTANT USER INFORMATION

100% use of a working hearing protector is the only sure protection
from hearing loss.
If you spend time in environments with more than 85 dB A-weighted
noise, you need to protect your hearing, because the hearing recep-
tors deep in your ears may be irreparably damaged. If you remove
the protectors for even a tiny portion of the time you spend in noisy
situations, you are in the danger zone.
A comfortable hearing protector designed for the specific noise
level in which it is used is the best guarantee that you will wear
the hearing protector 100% of the time, thereby ensuring protection
from permanent hearing loss.