Quick ASTER AS 312 Manuel De L'utilisateur page 17

POS. DESCRIPTION
9 Screw
10 Mooring rope puller
11 Spring for pressure lever
12 Mooring rope puller pin
13 Pressure lever
14 Screw
15 Rope/chain stripper "AS"
16 Chain guide cover
17 Base
18 Plug
19 Gasket / jig Aster
20 Sensor
21 Circlip
22 Bearing
23 Flange
24 Shaft 300/500W
25 Long shaft 300/500W
26 Key
27 Key
28 Stud
29 Gearbox flange gasket
Top TG40
30A Gearbox 500W Quick TG40 series SLMR05TG4000
30B Gearbox "Hi Speed" 500W TG40
31 Washer
32 Spring washer
33 Nut
34 Screw
35 Geared motor seal
36A Key
36B Electric motor 300W 12V
36C Electric motor 500W 12V
37 Electric motor 500W 24V
38 Flange gasket
39 Motor casing watertight 300/500W PCCCPM040000
40
Poles gasket
electric motor 300/500W
41 Bottom protec cover
electric motor 300/500W
42 Screw
ASTER 300/500W - REV006A
CODE
MBV0410MXTSC
MMSTTC08ASC0
MMTND08ASC00
Quick
MMTC08ASC000
ant to marine environments. In any case, any salt deposits
PDLVTD08ASCN
on the outside must be removed periodically to avoid cor-
MBV0512MXCE0
rosion and damage to the equipment. The parts where salt
MSN10ASX0000
may have built up should be washed thoroughly with fresh
SGMSGG08ASC1
water.
SGMSC08ASC00
MSR08XASC000
Once a year, the drum and the gypsy are to be taken apart
PGBSG10AS000
as follows:
KNREEDCL0000
MBAE3015Y000
DRUM VERSION
MBJ160060000
Use the handle (1) to loosen the bush (2); pull off the drum
MSVFLPRAS000
(3) and the top clutch cone (5); loosen the fixing screws (14)
MSAS05206R00
of the rope/chain stripper (15) and remove it. Pull off the
MSAS05245R00
gypsy (6).
MBH0606050X0
MBH0606020X0
NO-DRUM VERSION
MBP080607X00
Use the handle (1) to remove the gypsy cover (4); remove
the top clutch cone (5); loosen the fixing screws (14) of
PGFLRDTG4000
the rope/chain stripper (15) and remove it and pull off the
gypsy (6).
SLMR05TG40HS
MBR08X000000
Clean all the parts removed to avoid corrosion, and grease
MBR08XDE0000
the shaft thread (24 and 25) and the gypsy (6) where the
MBD08MXEN000
clutch cones rest (5 and 7).
MBV0516MXE00
PGBMR0400000
Remove any oxide deposits from the terminals of the elec-
MBH040415F00
tric motor and the reversing contactor unit; grease them.
EMF031200000
EMF051200000
EMF052400000
PGGPMFN04000
PGGPMPM04000
PCCPPMFN0400
MBV03916AXCC
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17