Extended Modes - Petsafe Petporte smart flap Guide D'installation

Extended Modes

The Petporte smart flap 's "extended mode" system gives you the opportunity to tailor the Petporte smart flap
®
To enter the Extended Modes menu, press both the Red and Green Buttons simultaneously for 2 seconds, or until both lights begin to flash, and then release
them. The Petporte smart flap should beep and the green light will come on to inform you that you have now entered the first of the Extended Mode menu
®
options.
When in "extended mode", the modes are selected by pressing the Red Button to go "up" a mode and the Green Button to go "Down" a mode. The current
mode is indicated by a number of beeps. When you are in the mode you require, a quick press of both buttons simultaneously will activate that mode. See
page 14 for a table of available extended modes. If no buttons are pressed within a 20 second period, the Petporte smart flap
will extinguish, indicating that the unit has gone back to its normal mode of operation.
Exit Mode (leave Extended Modes) - 1 Beep
This is the first mode in the Extended Mode menu. It is indicated by a single audible beep. This option simply cancels the "extended mode" and puts the
Petporte smart flap back into a normal mode of operation. To activate Exit Mode, quickly press both Red and Green buttons simultaneously.
®
Open Mode - 2 Beeps
In the unlikely event that you wish to have the Petporte smart flap
animal (be it microchipped or not) can enter through the Petporte smart flap
for more than 2 seconds then push the red button once to enter Open Mode which will be indicated by 2 beeps. Then, to activate Open Mode and exit the
extended modes quickly press both Red and Green buttons simultaneously.
When Open Mode is activated the unit will emit a long beep and the green light should flash to show the unit is in Open Mode.
To de-activate Open Mode, activate the Open Mode once more. The unit will again emit a long beep and the green light should extinguish, indicating the
Petporte smart flap has returned to a normal mode of operation.
®
Silent Mode 3 - Beeps
Each time that a recognised animal enters or leaves via the Petporte smart flap
Enter the Extended Modes by pushing the Red and Green buttons simultaneously for more than 2 seconds then push the red button once (the unit will emit 2
beeps) then again to enter Silent Mode which will be indicated by 3 beeps. Then to activate silent mode and exit the extended modes quickly press both buttons
simultaneously. A short beep should be heard, following which no further beeps will be emitted whenever your pet enters or exits the Petporte smart flap
To turn the beep back on, activate the Silent Mode once more. The unit will again emit a short beep, following which a short beep will be emitted whenever
your pet enters or exits the Petporte smart flap
Set Light Level Mode - 4 Beeps
When the Petporte smart flap is set to Night Mode the light sensor detects a pre-determined level of ambient light and locks or unlocks the Petporte smart
®
flap ® accordingly.
If you wish to alter when the Petporte smart flap
the outside light is enough for your cat to be safely outside. Make sure that your indoor lights are switched off when you re-set the light level; otherwise they
may influence the light sensor. Enter the Extended Modes by pressing the Red and Green buttons simultaneously for more than 2 seconds, then press the red
button once (the unit will beep twice), then press the red button again (the unit will beep 3 times) then press the red button once again and the unit will beep
4 times as you enter Set Light Level Mode. To select the current light level, at which you want the door to lock or unlock, press the Red and Green buttons
simultaneously. The unit will emit a beep and exit the Extended Modes.
16
open to allow any animal entry, the Petporte smart flap
®
. Enter the extended modes by pushing the Red and Green buttons simultaneously
®
®
.
®
locks or unlocks in Night mode, simply activate the Set Light Level mode, in the morning or evening, when
®
www.petsafe.net
to your individual requirements.
®
the unit will emit a short beep. To silence this beep, activate the Silent Mode.
will beep and the green light
®
provides a mode whereby any
®
.
®