Cleaning And Maintenance - Campingaz ATTITUDE 2go Mode D'emploi

5. Use a gas leak solution to test for leaks.
6. Apply the solution to the connections between cylinder /
regulator/ hose / appliance. (Fig.4)
7. Open the gas cylinder valve (The control knob should
remain in the "OFF" (O) position). Bubbles in the gas leak
solution indicate that there is a gas leak.
8. To plug the leak, tighten the regulator nut on the gas
cylinder.
9. The stove must not be used until all leaks have been
eliminated.
10. Close the valve on the gas cylinder..
11. Unplug the regulator from the gas cylinder and contact
your local after-sales service centre for assistance.
Important:
Check for leaks at least once per year and each time the gas
cylinder is replaced.
H. PRIOR TO USE
Never use the appliance until the instructions have been read
carefully and understood. Additionally, ensure that:
y There are no leaks.
y Make sure the burner tube is not clogged (by spider webs,
etc.).
y The hose does not touch any components which may get
hot. (Fig. 3)
y The ventilation openings in the cylinder storing compartment
(if present) are not obstructed.
y The grease recovery tray fits correctly and that it is inserted
as far as it will go(Fig. 5).
Put the grates in place correctly (Fig 6)
I. LIGHTING THE BARBECUE BURNERS
Never light the appliance with the lid closed, only with the lid
opened.
1. Open the cooking lid.
2. Make sure the control knob is in the "OFF" position (O)
(Fig. 8).
3. Press the control knob and then turn it counterclockwise to
the full flow position (
4. Wait 2 to 3 seconds and push the piezo switch (
times (Fig. 7).
5. If the electronic ignition doesn't work, use the manual
ignition (see below)
J. LIGHTING THE BARBECUE MANUALLY
1. Open the cooking lid and remove the grates.
2. Make sure the control knob is in the "OFF" position (O)
3. Light a match and hold it up to the burner.
4. (Fig. 7-A) Push the control knob and turn it counterclockwise
until it is in the full flow position (
5. Put the grids back in place.
K. EXTINGUISHING THE BARBECUE
Put the control knobs back in the "OFF" position (O) and close
the gas cylinder valve(Fig 8).
L. REPLACING THE GAS CYLINDER
1. Always work in a well ventilated area and never in the
presence of a flame, spark or heat source.
2. Put the control knobs back in the "OFF" position (O) and
close the gas cylinder valve.
3. Remove the regulator, check that the sealing joint is in good
condition.
) (Fig.7) .
) several
). (Fig.7)
4. Put the full cylinder in place, refit the regulator, taking care
not to apply stress to the hose. Check for gas leaks.
M. OPERATION
It's recommended that protective gloves be worn to handle
components which may be very hot.
When used for the first time, heat up the barbecue with its
burners in full on position (
approximately 30 minutes in order to eliminate any odors
resulting from the paint on the new parts.
It is good practice to pre-heat your grill for a few minutes
(10-15min) before you start placing food on it. Similarly, to
when you cook in a pan or in an oven, it helps you to reach
an appropriate grilling temperature and prevents food from
sticking, ensuring a crisp, brown crust. To reduce the risk of
food sticking to grates further, you can lightly brush cooking oil
on the grids, prior to use.
Cooking speed can be regulated via the control knobs:
between the full flow position (
In order to reduce the amount of grease catching fire while
cooking, remove any surplus fat from the meat prior to placing
it on the grid.
Clean the barbecue after each use to prevent grease build up
and reduce the risk of ignition.
Important: If the burner turns off while using the appliance,
immediately turn the control knob to the "OFF" position
(O). Wait five minutes to allow the unburned gas to
escape. Only carry out the lighting steps after this time.
N. CLEANING AND MAINTENANCE
Never modify the appliance: any modification may prove
dangerous.
y In order to maintain your appliance in perfect operating
condition, it is recommended that you clean it after each use.
y Wait until the appliance has cooled down before cleaning.
y Close the gas cylinder and remove the regulator.
Burner :
Clean the burner using a damp sponge (soaked in water and
dishwashing soap). If necessary, use a wet steel brush.
Check that all burner outlets (OH) are clear and dry before
using again. If necessary, use a wire brush to unclog the
burner outlets.
If necessary, clean the burner or burner openings.
NOTE: Regular cleaning extends the lifetime of the burner and
prevents premature oxidation that may result from cooking
acid residue. Oxidation of the grill burner is, however, normal.
Control panel
Clean the control panel from time to time using a sponge
damped with dish washing liquid. Do not use abrasive
products.
Firebox wall:
Clean the bottom of the grill after each use with a damp
sponge.
Grease recovery tray:
Your barbecue is equipped with a grease recovery tray (Fig. 5).
It is recommendable to clean it after each use.
To facilitate cleaning, some sand can be placed at the bottom
of the grease recovery tray to absorb the cooking grease.
Discard the sand after each use.
Cooking grids
Cooking grids are enamelled.
Wait for them to cool before any cleaning operation. Use
a Campingaz BBQ Cleaner Spray cleaning product and
®
brushes for barbecues.
9
) (with the lid closed), for
) and low flow position ( ).
GB