Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
FPPS 9-3.6W-CL PLUG-IN POWER ADAPTER
ITEm NO.: 51 42 29
INTENDED USE
This product supplies voltage to electrical consumers with a 9 V battery terminal. The connected load's current consumption
must not exceed the maximum output rating of the product. Power is supplied via a standard mains socket (100 – 240 V/
AC, 50/60 Hz). The product should only be used in dry indoor areas. The product features both short-circuit and overload
protection.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product for purposes
other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short
circuiting, fire, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties
only together with its operating instructions.
DELIVERy CONTENT
•
Power adapter
•
Operating instructions
SAFETy INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety information. If you do
not follow the safety instructions and information on proper handling in this manual, we assume no
liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a)
Persons / Product
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material for
children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable
gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental
use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
•
Also observe the safety and operating instructions of any other devices which are connected to the product.
•
Sufficient ventilation is essential when operating the product. Do not cover the product. Never place the product
on a table cloth or on a carpet. Place it on a hard, flame resistant base.
•
The product should not be used immediately after it has been brought from an area of cold temperature to an
area of warm temperature. Condensed water might destroy the product. Wait until the product adapts to the
new ambient temperature before use.
•
Make sure that the output of the power adapter is not short-circuited.
•
Never pour liquids over electrical appliances and never leave objects filled with liquids (e.g. vases) on it or in
the vicinity. There is a high risk of fire or life-threatening electric shock.
•
Always lay the cables so that nobody can trip over or become entangled in them. This poses a risk of injury.
•
When setting up the product, make sure that the cable is not pinched, kinked or damaged by sharp edges.
•
The plug must be pulled out of the socket under the following conditions:
-
before cleaning the product
-
during a thunder storm
-
if the product is not being used over a long period.
b)
miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
If you are not sure about the correct connection or use, or if questions arise which are not covered by these operating
instructions, please do not hesitate to contact our technical support or another qualified specialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 180/586 582 7.
OPERATION
The device is not a charging device for rechargeable batteries. Under no circumstances try to charge a
rechargeable 9 V monobloc battery with this product.
1.
Connect the 9 V monobloc battery plug to the switched-off consumer.
2.
Connect the mains plug to a standard mains socket (100 – 240 V/AC, 50/60 Hz). The LED on the top of the power
adapter indicates operational readiness.
3.
Now switch the connected consumer on. If it does not function properly, switch it off immediately and disconnect it from
the power adapter.
VERSION 04/12
4.
Remove the power adapter from the mains when it is no longer in use.
CLEANING
•
When cleaning, the power adapter must be disconnected from mains socket and electrical loads.
•
Only use dry and soft cloth to clear the housing of the power adapter.
•
Do not use abrasive or solvents.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the household waste!
At the end of its service life, dispose of the product according to the relevant statutory regulations.
TEChNICAL DATA
Input voltage:
Output voltage:
Output current:
Output power:
Connection:
Cable length:
Operating temperature:
Storage temperature:
Dimensions (W x H x D):
Weight:
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Voltcraft®
100 – 240 V/AC, 50/60 Hz
9 V/DC
400 mA
3.6 W
9 V monobloc battery terminal
1.8 m
0 to +35 ºC, 20 – 85 % RH
-20 to +60 ºC, 10 – 90 % RH
68 x 39 x 68 mm
75 g
Publicité
