Remote Control; General Tips - EWT OMC500L Instructions D'installation

• is the reduce fl ame button for the left had side of the appliance. Press this to reduce the height/intensity of your
fl ame. You will hear an audible beep when you reach the minimum level
• is the increase fl ame button for the left had side of the appliance. Press this to increase the height/intensity of
your fl ame. You will hear an audible beep when you reach the maximum level
• is the reduce fl ame button for the right had side of the appliance. Press this to reduce the height/intensity of your
fl ame. You will hear an audible beep when you reach the minimum level
• is the increase fl ame button for the right had side of the appliance. Press this to increase the height/intensity of
your fl ame. You will hear an audible beep when you reach the maximum level

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping fi t them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button on Button Panel 'A', the LED's will start to blink on and off. This is to let you know that the appliance is ready to
connect to the remote control. Press the
control is paired to the appliance.
The operation of the remote control is the same as described in 'Receiver Controls'. You can pair multiple products to
the one remote control by repeating the pairing operation as above on your subsequent products.
The operation of the remote control is the same as described in 'Receiver Controls'.
Maintenance

GENERAL TIPS

Only use fi ltered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
CLEANING
Warning – Always press Switch 'A' to the 'OFF' (0) position (Fig.9) and disconnect from the power supply before
cleaning the fi re.
We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-
Water Tank, Sump, Nozzle, Tank cap and seal, Air fi lter.
For general cleaning use a soft clean duster – never use abrasive cleaners.
To remove any accumulation of dust or fl uff the soft brush attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
Water tank
1. Remove water tank, by fi rst disconnecting the LED Log Fuelbed as described earlier. By holding the center logs with
both hands gently lift off the fuelbed and set aside. Lift out the tank, place it into a sink and empty water.
2. Using a soft brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the outer
groove and the center rubber seal.
3. Put a small quantity of washing up liquid into the tank, refi t the cap and shake well, rinse out until all traces of
washing up liquid are gone.
4. Refi ll with fi ltered tap water only, replace the cap, do not over tighten.
Sump
1. Press Switch 'A' to the 'OFF' (0) position (Fig.9)
2. Gently lift out the fuelbed and place carefully on the ground
3. Remove the water tank by lifting upwards or in the case of a Mains Water, disconnect the 'fi ll cap' by turning it
clockwise until it clicks out of the locked position. You can now turn it away from the sump.
4. Disconnect the electrical connector, located on the right side of the sump. (Fig.10).
5. There are two clips, one on the left and one on the right hand side of the sump, holding down the sump. On the left
side press in the clip with one hand and with the other lift the nozzle our of the clip. Repeat this for the right side
(Fig.11). The nozzle is now released, lift this off and place aside (Fig.12)
6. Gently lift up the sump (Fig.13), taking care to keep level so as not to spill any water. Sit the sump in the sink.
7. Carefully empty the sump into the sink taking note that the transducer is held in place by a retaining clip.
8. Put a small amount of washing up liquid into the sump, and using a soft brush, gently clean all surfaces in the sump
and gently clean the transducer including the metal discs located in the top grooved surface.
9. When cleaned, thoroughly rinse the sump with clean water to remove all traces of washing up liquid.
10. Clean the Nozzle with the a soft brush and fl ush out thoroughly with water.
11. Reverse the above steps to reassemble.
button on the remote control. The appliance will switch off. Now the remote
12