SECTION 6
Wiring
CAUTION:
IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL
ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL
WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.
3
Examine the wire compartment cover and select the most convenient wire entrance
and remove the knock out. Feed the supply wire through the opening and install an
appropriate strain relief. Connect the white wire from the power unit to the white wire
from the supply. Connect the black wire from the power unit to the black wire of the
supply. Connect the ground wire from the home (green or bare) to the ground wire of the
power unit (green or green/yellow). Use approved methods for all connections (Figure 5).
Supply from home
Hot (Black)
Ground (Green or Bare)
Figure 5
2.
Attach the wire compartment to the power unit with two of the provided #6 blunt tipped
screws (Figure 6).
Wire Compartment
Figure 6
SECTION 7
Finishing the Installation
1.
Remove any protective plastic adhered to the power unit.
2.
Remove the lens covers, install the two included 18 Watt compact fluorescent lamps by
fully inserting lamp base into the lamp holder, and replace the lens covers.
3.
Turn switches to the OFF ( • ) position and restore power. Test that the light and the fan
are operating properly.
4.
If there is any vibration noise, check for the source and try to tighten fasteners, adjust
the tape to make a tighter connection or seal, or check that the hood collar damper, wall
damper or ceiling damper are opening properly.
SECTION 8
Operation
Controls
Your Range Hood is equipped with two rotary switches with one controlling the lighting and
the other controlling the exhaust fan blower. The light switch has three positions, High, Low,
and Off. The fan switch has four positions, Off, High, Medium, and Low (Figure 7).
6728028 Rev. L 12-15
ALL ELECTRICAL CONNECTIONS MUST BE MADE
Neutral (White)
From Hood
Figure 7
SECTION 9
Maintenance
CAUTION:
SERVICE PANEL BEFORE SERVICING THE UNIT.
Filters
1.
Included with your unit are aluminum grease filters that should be washed at least
once a month. The filters are dishwasher safe and should be washed in a mild soap or
detergent.
2.
To remove the filters, pull down on the handle tab until the filter releases from the unit. To
reinstall, slide tab at rear of filter into slot in the unit. While holding in handle of filter, lift
filter into place and release handle. The filter should snap securely into place (Figure 8).
Tab
Figure 8
3.
If the grease filters become damaged, replace with the Air King Model SVGF-03 Grease Filters.
Changing the Lamp
Remove the lamp cover on the underside of the hood. Remove lamp by gently twisting the lamp
base counterclockwise while applying outward pressure. Installation is the reverse of removal.
Replace with Air King model 26SBL or a compatible GU24 26 watt self ballasted lamp.
Night Light: Unscrew night light bulb from socket and replace with a 4 watt maximum type
C7 (candelabra base) night light bulb.
Fuse
To replace the fuse, turn the fuse cap located next to the wire connector counter clockwise
and pull out. Replace with a Bussman MDA-1.5 or equivalent 250-Volt, 1-1/2 Amp Max. fuse.
Reinstall the fuse back into the hood.
Cleaning
CAUTION:
CLEANSERS, ETC., AS THEY MAY DAMAGE THE RANGE HOOD.
1.
Clean your power unit with a mild detergent, such as dishwashing liquid, and dry with a soft
cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS. Completely dry before
restoring power. NEVER IMMERSE ELECTRICAL PARTS IN WATER.
2.
The fan assembly can be vacuumed when build up (dirt, lint, etc.) accumulates over time.
The fan is permanently lubricated and does not require oiling.
CALIFORNIA RESIDENTS ONLY:
WARNING:
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.
WARNING:
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE REPRODUCTIVE
TOXICITY.
www.airkinglimited.com
MAKE SURE POWER IS SWITCHED OFF AT
DO NOT USE GASOLINE, BENZINE, THINNER, HARSH
THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
3 of 12