Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

IMPORTANT INSTRUCTIONS -
ESQZ Series
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN
THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to
WARNING:
ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE
FOLLOWING:
a)
Use this unit only in the manner intended by the manufacturer.If you have questions,
contact the manufacturer.
b)
Before servicing or cleaning the unit, switch power off at service panel and lock the
service disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
WARNING:
ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE
FOLLOWING:
a)
Installation work and electrical wiring must be done by qualified person(s) in accordance
with all applicable codes and standards, including fire-related construction.
b)
Sufficient air is needed for proper combustion and exhausting of gases through the
flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating
equipment manufacturer's guideline and safety standards such as those published by
the National Fire Protection Association (NFPA) and the American Society for Heating,
Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c)
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
CAUTION:
USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.
CAUTION:
PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE - DO NOT
VENT EXHAUST AIR INTO SPACES WITHIN WALLS OR CEILINGS OR INTO ATTICS, CRAWL
SPACES, OR GARAGES.
d)
Ducted fans must always be vented to the outdoors.
e)
This unit must be grounded.
f)
To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall
spray, construction dust, etc. off power unit.
g)
Read all instructions before installing or using range hood.
WARNING:
SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED
CONTROL DEVICE.
6728010 Rev H 12-18
OPERATING MANUAL
AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
person, including the following:
TO REDUCE THE RISK OF FIRE,
TO REDUCE THE RISK OF FIRE,
FOR GENERAL VENTILATING USE ONLY. DO NOT
TO REDUCE THE RISK OF FIRE AND TO
TO REDUCE THE RISK OF FIRE, ELECTRIC
SAVE THESE INSTRUCTIONS
a)
Never leave surface units unattended at high settings. Boil overs cause smoking
and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
b)
Always turn hood ON when cooking at high heat or when flambéing food (ie. Crepes
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c)
Clean ventilating fans frequently. Grease should not be allowed to accumulate on
fan filter.
d)
Use proper pan size. Always use cookware appropriate for the size of the surface
element.
a)
SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off
burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
b)
NEVER PICK UP A FLAMING PAN - You may be burned.
c)
DO NOT USE WATER, including wet dishcloths or towels -
a violent steam explosion will result.
d)
Use an extinguisher ONLY if:
I.
You know you have a Class ABC extinguisher, and you already know how to
operate it.
II.
The fire is small and contained in the area where it started.
III.
The fire department is being called.
IV.
You can fight the fire with your back to an exit.
WARNING:
THE BUILDING HAS A STRONG EFFECT ON THE AIR FLOW, NOISE AND ENERGY
USE OF THE FAN. USE THE SHORTEST, STRAIGHTEST DUCT ROUTING POSSIBLE FOR
BEST PERFORMANCE, AND AVOID INSTALLING THE FAN WITH SMALLER DUCTS THAN
RECOMMENDED. INSULATION AROUND THE DUCTS CAN REDUCE ENERGY LOSS AND
INHIBIT MOLD GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY NOT ACHIEVE
THEIR RATED AIRFLOW.
www.airkinglimited.com
Range Hood
WARNING:
TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
WARNING:
TO REDUCE THE RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:
WARNING:
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
THE DUCTING FROM THIS FAN TO THE OUTSIDE OF
1 of 12

Publicité

Table des Matières
loading

Sommaire des Matières pour AirKing ESQZ Serie

  • Page 1 IMPORTANT INSTRUCTIONS - OPERATING MANUAL ESQZ Series Range Hood READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
  • Page 2 SECTION 3 INSTALLATION INSTRUCTIONS Prepare the Hood for Installation CAUTION: MAKE SURE POWER IS SWITCHED OFF AT Choose the type of ducting you will require. To ensure the best air and sound performance, SERVICE PANEL BEFORE STARTING INSTALLATION. it is recommended that the length of ducting and the number of elbows be kept to a minimum, the radius of each elbow be as large as possible for the installation, and that SECTION 1 hard ducting be used.
  • Page 3 SECTION 6 Hood Ducting Body E-22A/RCD7 CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES. Damper NOTE: The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended.
  • Page 4 SECTION 8 Changing the Lamp Remove the lamp cover by squeezing in the sides. The cover is held in place by tension Operation against the tabs on the hood. Controls LED Lamp: Remove lamp by gently twisting counterclockwise to release the lamp from Your Range Hood is equipped with two rotary switches with one controlling the lighting and the the base.
  • Page 5: Troubleshooting Guide

    Troubleshooting Guide Trouble Probable Cause Suggested Remedy 1. Hood does not operate when the switch is on. A fuse may be blown or a circuit tripped. Replace fuse or reset circuit breaker. Wiring is not connected properly. Turn off power to unit. Check that all wires are connected. 2.
  • Page 6 REPLACEMENT PARTS DIAGRAM Qty. Description Replacement Part # Motor 5S1146001 Motor Pad 5S1146002 Undercarriage (White) 5S1146003 Undercarriage (Black) 5S1146063 Impeller 5S1146012 Filter GF-08 5S1146004 Filter CF-08 5S1146005 Wire Compartment Cover 5S4199005 Lamp Holder 5S1146006 6 watt LED Lamp 5S1299725 Night Light Lamp Holder 5S1146007 Light Lens 5S4109005...
  • Page 7: Hotte De Cuisinière

    INSTRUCCIONES IMPORTANTES – MANUAL DE OPERACIÓN Séries ESQZ Hotte de cuisinière LIRE ET CONSERVER CES INSTRUCTIONS LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ. FAILLIR À SE CONFORMER AUX INSTRUCTIONS PEUT RÉSULTER EN BLESSURE PERSONNELLE GRAVE ET/OU EN DOMMAGE À...
  • Page 8 SECTION 3 INSTRUCTIONS D’INSTALLATION Préparez la hotte pour l’installation MISE EN GARDE : ASSUREZ-VOUS QUE Choisir le type de conduits qui sera requis. Pour garantir la meilleure qualité d’air et L’ALIMENTATION ÉLECTRIQUE EST COUPÉE À PARTIR DU PANNEAU DE performance acoustique, il est recommandé que la longueur de la canalisation et le DISTRIBUTION AVANT DE COMMENCER L’INSTALLATION.
  • Page 9 REMARQUE : NE PAS déconnecter quelque fil qui ait déjà été serti avec un connecteur de fil à l’usine. Hotte Placez le couvercle du compartiment de fils et serrez la vis. Assurez-vous que tous les E-22A/RCD7 fils sont placés de manière sécuritaire à l’intérieur du compartiment. Onglets SECTION 6 Clapet...
  • Page 10: Entretien

    SECTION 8 Changement de la lampe Retirez l’écran protecteur de lampe en appuyant sur les côtés. Le panneau est maintenu Opération en place grâce à la pression exercée sur les languettes de la hotte. Contrôles Ampoule LED : Retirez la lampe en tournant attentivement dans le sens contraire des Votre hotte est munie de deux interrupteurs rotatifs dont un règle l’éclairage et l’autre le aiguilles d’une montre pour libérer la lampe de la base.
  • Page 11: Guide De Dépannage

    Guide de dépannage Trouble Cause possible Solution suggérée 1. La hotte ne fonctionne pas lorsque l’interrupteur 1a. Un fusible peut être grillé ou un disjoncteur peut Remplacer le fusible ou réinitialiser le disjoncteur. est à EN (ON). être déclenché. 1b. Le câblage n’est pas raccordé correctement. Couper l’alimentation de l’unité.
  • Page 12: Diagramme Des Pièces De Remplacement

    DIAGRAMME DES PIÈCES DE REMPLACEMENT # de pièce de Qté. Description remplacement Moteur 5S1146001 Plaquette de moteur 5S1146002 Châssis (Blanc) 5S1146003 Châssis (Noir) 5S1146063 Hélice 5S1146012 Filtre (GF-08) 5S1146004 Filtre (CF-08) 5S1146005 Couvercle de compartiment à câblage 5S4199005 Support à lampe 5S1146006 Lampe de 6 watts LED 5S1299725...

Table des Matières