First Use And Charging; Using The Shaver - Braun 9 Série Mode D'emploi

Our products are designed to meet the highest
standards of quality, functionality and design.
Thank you for your trust in Braun's quality, and we
hope you enjoy your new Braun shaver.
Warning
Only models 9080s/9040s w&d can be used with
foam or gel.
Clean&Charge Station (models 9095cc w&d/
9090cc/9075cc/9070cc/9050cc)
To prevent the cleaning fluid from leaking, ensure
that the Clean&Charge Station is placed on a flat
surface. When a cleaning cartridge is installed,
do not tip, move suddenly or transport the station
in any way as cleaning fluid might spill out of the
cartridge. Do not place the station inside a mirror
cabinet, nor place it on a polished or lacquered
surface.
The cleaning cartridge contains a highly flammable
liquid so keep it away from sources of ignition.
Do not expose to direct sunlight and cigarette
smoking nor store it over a radiator.
Do not refill the cartridge and use only original
Braun refill cartridges.
Shaver
1 Foil & Cutter cassette
2 Cassette release buttons
3 MultiHeadLock switch
4 On/off switch
5 Shaver display
6 Long hair trimmer
7 Shaver-to-station contacts
8 Release button for long hair trimmer
9 Model number of shaver
10 Shaver power socket
11 Special cord set
12 Brush
13 Hard travel case

First use and Charging

Prior to first use remove the protection foil if any
from the shaver display. Connect the shaver to an
electrical outlet by snapping the special cord set (11)
into the power socket (10) or for cc models via the
Clean&Charge Station (see Chapter «Clean&Charge
Station»).
Charging and basic operating information
• When charging for the first time, charge continu-
ously for 1 hour.
• A full charge provides up to 50 minutes of cordless
shaving time. This may vary according to your
beard growth and environmental temperature.
• Recommended ambient temperature for charging
is 41 °F to 95 °F / 5 °C to 35 °C. The battery may
not charge properly or at all under extreme low or
high temperatures. Recommended ambient
temperature for shaving is 60 °F to 95 °F / 15 °C to
35 °C.
• Do not expose the shaver to temperatures higher
than 122 °F / 50 °C for extended periods of time.
• When the shaver is connected to an electrical
outlet, it may take some minutes until the display
illuminates.
Shaver display
Charge status
The shaver display (5) shows the charge status of
the battery when connected to an electrical outlet:
• During charging the respective battery segment
will blink.
• When fully charged all battery segments will light
up for a few seconds then the display turns off.
Low charge
The low-charge light
battery is running low. You should be able to finish
your shave. With switching off the shaver a beep
sound reminds of the low charge status.
Models 9095cc w&d/9090cc/9080sw&d: The last
9 minutes of remaining shaving time are displayed in
digits.
Cleaning status (models 9095cc w&d/9090cc/
9075cc/9070cc/9050cc)
The cleaning indicator
needs to be cleaned in the Clean&Charge Station.
Travel lock
The lock symbol lights up when the shaver has
been locked to avoid unintended starting of the
motor (e.g. for storing in a suitcase).

Using the shaver

Press the on/off switch (4) to operate the shaver.
Tips for a perfect dry shave
1. Always shave before washing your face.
2. At all times, hold the shaver at the right angle
(90°) to your skin.
3. Stretch your skin and shave against the direction
of your beard growth.
MultiHeadLock switch (head lock)
To shave hard-to-reach areas (e.g. under the nose)
slide the MultiHeadLock switch (3) down to lock the
shaver head. The shaver head can be locked in five
positions. To change position, move the shaver head
with your thumb and forefinger back or forth. It will
automatically click into the next position.
Models 9095cc w&d/9090cc/9075cc/9070cc/9050cc:
For automatic cleaning in the Clean&Charge Station
the head lock should be released.
flashes red when the
lights up when the shaver
(see fig. A)
9