Front Panel Features - Furman CONTRACTOR SmartSequencer Série Guide De Démarrage Rapide

FRONT PANEL FEATURES

COVER SHIELDS REMOVED
START
SEQUENCE
START SEQUENCE
PUSH BUTTON
START SEQUENCE PUSH BUTTON
Triggers sequence in remote mode.
• Activates or deactivates sequence
• Hold button to re-sync multiple sequencer
PRIMARY LINK
PRIMARY LINK DELAY 1 DELAY 1
START START
SECONDARY LINK SECONDARY LINK DELAY 2
DELAY 2
SEQUENCE SEQUENCE
ETHERNET ETHERNET DELAY 3 DELAY 3
DELAY INDICATORS
Duplex 1 is powered on
DELAY 1
Duplex 2 is powered on
DELAY 2
DELAY 3 Duplex 3 is powered on
Delay 3 contacts react in time with DELAY 3 Outlets
DIP SWITCH MATRIX AND TIME CALIBRATION (diagrams below)
1M = 1 Minute Delay
DIP 1
DIP 2
2M = 2 Minute Delay
DIP 3
4M = 4 Minute Delay
NOTE: DIP 1, 2 & 3 can be summed together up to 7 minutes.
DIP 4
N.O. / N.C. sets Forced Off alarm poles
The out of the box factory setting is "normally open".
When sequence is "ON". Switched outlets will be ON
until a dry contact closure is applied across the
FORCE OFF poles.
DIP SWITCH CLOSE-UP
1 2 3
4M
1M 2M
DLY
ADJ
GND MOM
PRI
ON MNT
SEC
6 7
3
PRIMARY LINK
DELAY 1
SECONDARY LINK
DELAY 2
ETHERNET DELAY 3
CONNECTION STATUS
LIGHTS
BASIC POWER MANAGEMENT
• UNSWITCHED OUTLET - 15A Courtesy Outlet
CN-1800S & CN-2400S
s • CIRCUIT BREAKER- Press to reset in the event of
current overload.
1 1 2 2 3 3 4 4 5 5
12V ON POWER POWER
1M 1M 2M 2M PRIMARY LINK PRIMARYLINK 4M 4M N.O. N.O. 12V ON DELAY 1 DELAY 1
N.C. N.C. 12V OFF 12V OFF
DLY DLY SECONDARY LINK SECONDARY LINK PROTECTION OK DELAY 2
PROTECTION OK DELAY 2
ADJ ADJ
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
ETHERNET ETHERNET DELAY 3 DELAY 3
GND GND MOM MOM PRI PRI EVS AUTO EVS AUTO EXTREME VOLTAGE EXTREME VOLTAGE
ON ON MNT MNT SEC SEC MANUAL MANUAL
6 6 7 7 8 8 9 9
POWER PROTECTION INDICATORS
POWER
"Unswitched" outlets are active.
PROTECTION OK
illuminate if surge protection has been compromised.
DIP 5
Remote Mode (DIP 7 set to MNT)
Chooses +12V to REM pole functionality. In default
OFF mode, a dry closed contact across +12V to REM
triggers sequencer OFF. If ON mode, closed contact
triggers ON.
• 12V OFF = Short Deactivates
• 12V ON = Short Activates
DIP 6
Activates REM to GND pole functionality.
• REMOTE TO GROUND = ON
FACTORY DEFAULT SETTINGS - SET FOR 30 SECOND DELAY
4 5
POTENTIOMETER DEFAULT
N.O. 12V ON
SETTING - Time Delay
N.C. 12V OFF
Adjustment is set at
12:00 o'clock (50%)
Time Delay Adjustment ranges from
0.0% to 100%. The percentage is
multiplied with the DIP switch selec-
EVS AUTO
MANUAL
tions 1, 2 and 3.
8 9
DELAY ADJUSTMENT
1 2 3 4 5
N.O. 12V ON
1M 2M 4M
N.C. 12V OFF
DLY
ADJ
1 2 3 4 5 6 7 8 9
GND MOM
PRI EVS AUTO
ON MNT SEC MANUAL
6 7 8 9
DELAY DIP SWITCH POWER
INDICATOR MATRIX INDICATOR
LIGHTS LIGHTS
UNSWITCHED UNSWITCHED 4 5 6 7 8 9
1 2 3
1 2 3 4 5
N.O. 12V ON GND MOM PRI EVS AUTO 15 AMPS 15 AMPS
2M 4M
1M
4M ON N.O. MNT 12V ON SEC MANUAL
1M N.C. 2M 12V OFF
N.C. 12V OFF
DLY DLY
ADJ ADJ
1 2 3 4 5 6 7 8 9
GND MOM PRI EVS AUTO
1 2 3 4 5 6 7 8 9
ON MNT SEC MANUAL
6 7 8 9
PUSH TO RESET PUSH TO RESET
Indicates unit is receiving AC power and
Normally lit, dims or will not
12VDC ON/OFF sets +12V pole in
GROUND ON / OFF
DLY
ADJ
UNSWITCHED
15 AMPS
POWER
PROTECTION OK
EXTREME VOLTAGE
PUSH TO RESET
UNSWITCHED
CIRCUIT
OUTLET
BREAKER
KEYSWITCH SETTINGS
3 position ON/OFF Security Switch
• OFF = Bypasses remote sequenced outlets to OFF
• REMOTE = Engages and activates remote features
• ON = Bypasses remote sequenced outlets to ON
NOTE: Settings affect COMM port (see full manual)
UNSWITCHED UNSWITCHED
REMOTE REMOTE
20 AMPS 15 AMPS
POWER POWER
PROTECTION OK
PROTECTION OK
OFF OFF ON
ON
EXTREME VOLTAGE EXTREME VOLTAGE
PUSH TO RESET PUSH TO RESET
EXTREME VOLTAGE
voltage condition is present (consequently, all outlets
are powered off). EVS auto reset is controlled by
(DIP 9) setting.
Maintained / Momentary
DIP 7
Sets contact closure preference for either
Maintained or Momentary switches.
NOTE: Momentary mode overrides DIP 5 and 6.
DIP 8
PRIMARY / SECONDARY
Delegates unit's role in command sequence.
DIP 9
EVS AUTO / MANUAL setting
Activates/Deactivates Extreme Voltage Shutdown
Auto Reset. Manual setting requires Key Switch
to be set OFF to clear EVS state.
NOTE: The DIP switch DIP SWITCH DEFAULT SETTING -
ON
ON / OFF settings are Switches are factory pre-set as shown
indicated as shown below. Switches 1, 4, 8, and 9 are up
below throughout (ON) position.
1 2 3 4 5 6 7 8
this manual.
ON
DLY
ON
ADJ
OFF
1
KEYSWITCH
REMOTE
OFF
ON
REMOTE
REMOTE
OFF OFF ON
ON
Illuminated when an extreme
9
2 3 4 5 6 7 8 9