Start Up Instructions; Product Registration; Changing The Filter Cartridges - Watts Pure H2O H2O-DWUF300 Manuel D'installation, D'utilisation Et D'entretien

Start up Instructions

Congratulations! You have completed the
installation of your new water filtration system.
Please Follow the Startup Instructions.
Step 1
- Turn on water
supply at angle
stop and open the
Adapt-a-Valve . Turn
faucet handle to
the open position
to start the flow of
water through the
unit . Run 3 gallons
of water through
the unit in order to flush out the normal black carbon
fines (it will "sputter" until the air is purged out) from
the unit . A container with a known volume can be
filled to determine how much water has flushed
through the system . Initially, the water may appear
cloudy which is due to tiny air bubbles and it will
clear up shortly . Close the faucet when finished .
Step 2
- Check for leaks . If you have any leaks, shut off the
water supply to your system, tighten any fittings /
housings then turn the supply back on .
NOTICE
Check frequently over the next 24 hours to ensure no leaks
are present

Product Registration

To Register your product, please visit www .watts .com/pureh2o
and select "Register Now" . Watts is concerned for the safety of
your personal information . Watts collects personal information
when you register with Watts . This information is stored in our
data base and we do not rent, sell, or share personal information
with other people or nonaffiliated companies . We will send you
certain types of communications such as direct mail, email, or
by telephone relating to our products or products that you have
purchased only with your prior permission . We limit access to
your personal information to those employees who will directly
provide you with services or products in order to do their jobs .
See our privacy policy at - http://www .watts .com/privacy .asp
See Terms of Use at - http://www .watts .com/terms .asp

Changing the Filter Cartridges

Your system is equipped with valved heads which will
automatically turn off the water supply to each filter when the filter
is released, thus you do not need to turn off the incoming water
supply at the Adapt-a-Valve . The faucet must be off when filters
are replaced . To make the removal of the filter cartridges easier,
the heads & cartridges may be swiveled up to 90 degrees .
6 Month System Maintenance
Replace:
Sediment - Every 6 months
PN# 88005215- H20-F14
Carbon block - Every 6 months or after 2000
Gallons PN# 88005217 H2O-F12
12 Month System Maintenance
Replace:
To buy replacement part(s) please visit the retail store or their
website or contact Watts retail customer service at
(888) 321-0500
Step 1:
ON
Step 2:
Step 3:
NOTICE
If the new filter cartridge won't snap in easily or pops off it may
be due to high incoming water pressure. Relieve pressure to the
system by turning off the water supply using the Adapt-A-Valve
and then install the cartridge. Once the cartridge is seated, turn the
water supply back on to your unit.
Step 2
Step 3-2
NOTICE
2-stage model shown above. Tubing not shown in above pictures.
Do not remove the tubing while changing the filter.
Page 7
Ultra Filtration Membrane - Every 12 months
PN# 88005447- H20-F15
Place a towel under the filter module to catch any
excess water that may drip out from the filters during
the changeover .
To remove a filter cartridge: Push & hold the button
on the valved head above the filter . Twist filter
counter-clockwise for about 45 degrees while pulling
downward (from the head) Release button and
discard old filter .
To install a filter cartridge: Remove the seal cap and
insert the cartridge into the filter head, push upward
and twist the filter clock-wise for about 45 degree
until you hear an audible "click" (the button does not
need to be pressed to install new filters) .
Step 3-1
Step 3-3