Torque
N
Hex Wrench
Bolts (long)
[M6x32]
Base bracket
Bolts (long)
Base bracket
Cushion base
Body
Installing System Carrier
Installing INXR
Torque
N
Bolts (short)
Hex wrench
(M6x15)
Arrow
Base unit
Attaching the base brackets
Place the base bracket on the
cushion base. Secure them with the
long bolt [M6x32] (included) using the
Hex wrench (included) until the bolts
are firmly tightened while holding both
together parallel to the roof molding.
All base brackets (4 pcs.) are identical. The bracket is
symmetrical with respect to the side-to-side axis; its
installation orientation does not matter.
1
Place the base unit on the installed
cushion base/base bracket. Then using
the Hex wrench (included), tighten while
alternating between the right and left
bolts (short) [M6x15] (included)
until the bolts are firmly tightened.
The base unit must be placed as the
arrow on the unit faces toward the
vehicle center.
3109202TR1284C
Before using the Mounting hooks, carefully read the installation instructions as well as the installation
instructions for basic carrier systems, and follow all usage instructions. After reading the installation
instructions, keep it in a safe place along with the installation instructions for basic carrier systems. If you
are to give the mounting hooks to a third person, provide the installation instructions to ensure safe
installation and usage. If you have any questions regarding the installation instructions, contact our
customer service listed below.
Install hooks correctly at specified positions according to the installation instructions herein and the installation instructions for the
applicable carrier system. Installation positions of hooks depend on the vehicle type. If hooks are not installed at specified
positions, the carrier may fall and cause accidents. If the installation instructions appropriate for your vehicle type are not
available, contact our customer service listed below.
Select hooks matching your vehicle by referring to the Fit Guide available at stores or on our website : www.innoracks.com.
If inappropriate hooks are used, the carrier / attachment may fall and cause accidents.
Before driving the vehicle, rock the stays and bars in all directions to ensure that there is no looseness. Retighten any loose
knobs or bolts.
Do not use these hooks for attachments of non-specified types.
The carrier may fall and cause accidents.
Observe the specified loading conditions.
Failure to observe the loading condition may cause the carrier to break or loosen and fall, resulting in accidents.
EN
For INNO dedicated ski & snowboard carriers, read the carrier installation instructions to determine proper
mounting locations.
The TR Mounting hooks include the parts listed below. Verify that all of these parts are
included in the carrier system you have purchased. In the event any of these parts are
missing, contact our customer service listed below.
Punch mark FL
NOTE
The specifications or external appearance of this product or any of the genuine
spare parts may be changed for improvement without prior notification.
If you have any comments, questions or suggestions, contact our customer service listed below.
Car Mate USA shall not be held liable for any accidents or incidental losses arising from improper installations or usage.
Furthermore, Car Mate USA shall not be held liable for any accidents or incidental losses arising from installation or usage after
the customer has made any modifications to the system's original configuration or specifications.
If you can not find your vehicle on the following page(s), contact us for more information.
Car Mate USA, Inc.
383 Van Ness Ave., Suite 1603,
Torrance, CA 90501 U.S.A.
support@innoracks.com
-EN
-A
www.innoracks.com
TR Fit Hooks
Installation Instructions
WARNING
Punch mark FR
Punch mark RL
Punch mark RR
32mm
Contact Information
TR128
No.
Part
Qty
1
Cushion base FL
Cushion base FR
1
Cushion base RL
1
Cushion base RR
1
Base bracket
4
4
Spacer
4
Bolt [M6x32mm]
Protection sheet
8
1
Hex Wrench [B=4]
1
Installation Instructions
08 / 2014
3109202TR1281C
-EN
-A