Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Before using the Mounting hooks, carefully read the installation instructions as well as the installation
instructions for basic carrier systems, and follow all usage instructions. After reading the installation
instructions, keep it in a safe place along with the installation instructions for basic carrier systems. If you
are to give the mounting hooks to a third person, provide the installation instructions to ensure safe
installation and usage. If you have any questions regarding the installation instructions, contact our
customer service listed below.
Install hooks correctly at specified positions according to the installation instructions herein and the installation instructions for the
applicable carrier system. Installation positions of hooks depend on the vehicle type. If hooks are not installed at specified
positions, the carrier may fall and cause accidents. If the installation instructions appropriate for your vehicle type are not
available, contact our customer service listed below.
Select hooks matching your vehicle by referring to the Fit Guide available at stores or on our website : www.innoracks.com.
If inappropriate hooks are used, the carrier / attachment may fall and cause accidents.
Before driving the vehicle, rock the stays and bars in all directions to ensure that there is no looseness. Retighten any loose
knobs or bolts.
Do not use these hooks for attachments of non-specified types.
The carrier may fall and cause accidents.
Observe the specified loading conditions.
Failure to observe the loading condition may cause the carrier to break or loosen and fall, resulting in accidents.
For INNO dedicated ski & snowboard carriers, read the carrier installation instructions to determine proper
mounting locations.
The TR Mounting hooks include the parts listed below. Verify that all of these parts are
included in the carrier system you have purchased. In the event any of these parts are
missing, contact our customer service listed below.
①
Punch mark：FL
⑤
⑥ ⑦
NOTE
The specifications or external appearance of this product or any of the genuine
spare parts may be changed for improvement without prior notification.
If you have any comments, questions or suggestions, contact our customer service listed below.
Car Mate USA shall not be held liable for any accidents or incidental losses arising from improper installations or usage.
Furthermore, Car Mate USA shall not be held liable for any accidents or incidental losses arising from installation or usage after
the customer has made any modifications to the system's original configuration or specifications.
If you can not find your vehicle on the following page(s), contact us for more information.
Car Mate USA, Inc.
383 Van Ness Ave., Suite 1603,
Torrance, CA 90501 U.S.A.
support@innoracks.com
www.innoracks.com
Installation Instructions
WARNING
②
③
Punch mark：FR
Punch mark：RL
⑧
23mm
Contact Information
TR Fit Hooks
④
Punch mark：RR
⑨
⑩
TR124
No.
Part
①
Cushion base FL
②
Cushion base FR
③
Cushion base RL
④
Cushion base RR
⑤
Base bracket
⑥
Spacer
⑦
Bolt [M6x23mm]
⑧
Protection sheet
⑨
Hex Wrench [B=4]
⑩
Installation Instructions
9009211TR1241B
Qty
1
1
1
1
4
4
4
8
1
1
02 / 2014
-EN
Publicité
Table des Matières
Manuels Connexes pour INNO TR124
Sommaire des Matières pour INNO TR124
- Page 1 Observe the specified loading conditions. Failure to observe the loading condition may cause the carrier to break or loosen and fall, resulting in accidents. For INNO dedicated ski & snowboard carriers, read the carrier installation instructions to determine proper mounting locations.
- Page 2 TR124 Installation Procedure for the individual Vehicle Model Loading conditions Manufacturer Vehicle model Vehicle type Model year Bike Maximum Load Capacity CX-7 2007 - 2012 MAZDA ( Load + Base rack CX-9 2007 - + Attachments ) Vehicle preparations Cleaning the installation area on the...
- Page 3 Attach them to the nut on the vehicle as Hex wrench shown in the figure. All base brackets Bolts (long) (4 pcs.) are identical. The bracket is 23mm (M6x23) symmetrical with respect to the side-to-side Base bracket axis; its installation orientation does not matter.
- Page 4 Installing System Carrier (IN-XR) Installing base unit Place the base unit on the installed cushion base/base bracket, and using Bolts (short) Hex wrench the Hex wrench tighten alternately the (M6x15) right and left bolts (short) [M6 x 15] supplied with the carrier. 15mm Arrow The base unit must be placed as the...
-
Page 5: Installation Instructions
Le non-respect des conditions de charge peut faire casser le systéme de transport ou le faire se desserrer puis entraîner sa chute puis un accident. Pour les systèmes de transport spècifiques au snowboard et au ski INNO, lisez les modes d’emploi des systèmes de transport pour déterminer l’emplacement de montage approprié. -
Page 6: Procédure D'installation Pour Le Modèle De Véhicule Particulier
TR124 Procédure d’installation pour le modèle de véhicule particulier Conditions de charge Fabricant Modèle Type Année Vélo Capacité maximale de charge CX-7 2007 - 2012 MAZDA ( Charge + Le porteur CX-9 2007 - de base + Remorque ) Préparation du véhicule Nettoyage de la zone d’installation... - Page 7 Fixez-les à l’écrou du véhicule, tel qu’illustré Clé hexagonale dans la figure. Les supports de base Boulon (long) (4 unités) sont tous identiques. Les supports 23mm (M6x23) Support de base sont symétriques quant à leur axe transversal; la direction dans laquelle ils sont installés n’a pas d'importance.
-
Page 8: Installation De La Base
Installation du système de transport (IN-XR) Installation de la base Déposez la base sur le coussinet de base /support de base installé puis, Clé hexagonale Boulon (court) à l’aide de la clé hexagonale, serrez l’un (M6x15) après l’autre les boulons (courts) [M6 x 15] de droite et de gauche fournis 15mm avec le porteur. -
Page 9: Información De Contacto
No respetar las condiciones de carga puede provocar que el portacargas se rompa o se afloje y caiga, lo que causaría un accidente. Para los portacargas exclusivos para esquís y tablas de snowboard de INNO lea los manuales de instrucciones del portacargas para determinar las ubicaciones de montaje correctas. - Page 10 TR124 Procedimiento de instalación para modelos de vehículos individuales Condiciones de carga Fabricante Modelo Tipo Año Bicicleta Capacidad máxima de carga libras CX-7 2007 - 2012 MAZDA ( Carga + Perchas de la base + Dispositivo de CX-9 2007 - montaje ) Preparaciones del vehículo...
- Page 11 Conéctelas a la tuerca del vehículo como Llave hexagonal se muestra en la figura. Todas las Perno (largo) abrazaderas de base (4 pzas.) son 23mm (M6x23) Abrazaderas idénticas. La abrazadera es simétrica con de base respecto al eje de lado a lado; su Separador orientación de instalación no importa.
- Page 12 Instalación del sistema de portacargas (IN-XR) Instalación de unidad base Coloque el unidad base sobre la base del amortiguador/abrazadera de base Perno (corto) Llave Hexagonal instalada y con la llave Allen, apriete de (M6x15) manera alternada los pernos de la derecha e izquierda (cortos) [M6 x 15] 15mm Flecha...