Electrical Safety - ATIKA KSG 220 A Instructions D'utilisation

− wear a hair-net if your hair is long
Wear protective clothing:
− safety goggles
− ear protection (Sound intensity level at workplace can
exceed 85 dB (A))
− dust mask
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Take into consideration environmental influences:
− Do not use the device in moist or wet ambience.
− Do not expose the chain sharpener to rain.
− Do only work with sufficient visibility conditions. Provide
for good illumination.
Never leave the operational machine unattended.
Persons under the age of 18 must not operate the device.
Keep other persons away.
Do not allow other persons, especially children, to touch
the tool or cable.
Keep them away from your working area.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on
the machine that could impair the safety.
Do not use any grinding wheels which do not comply with
the indicated characteristics of this instruction manual.
The use of other tools and other accessories may
present a risk of injury to you.
Worn and defective grinding wheels (cracks, imbalance,
chipping, etc.) must be replaced immediately.
Ensure a firm seat of the grinding wheel.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− maintenance and cleaning
− Elimination of failures (including freeing a blocked
grinding wheel)
− Storage
− Leaving the chain sharpener (even in case of short-
term interruptions)
Caution! Grinding wheel runs after! Do not brake the
grinding wheel by hand or using lateral pressure.
Maintain your chain sharpener with care:
− Keep the device free of oil and grease.
− Follow the maintenance instructions and the
instructions for tool exchange.
Check the machine for possible damage:
− Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function.
− Check whether the movable parts function perfectly
and do not stick or whether the parts are damaged. All
parts must be properly mounted and all conditions met
to ensure the flawless operation of the chain sharpener.
− Unless otherwise indicated in the operating instructions,
damaged safety devices and parts must be properly
repaired or replaced by an authorised workshop (or by
the manufacturer).
− Damaged or illegible safety warning labels should be
replaced immediately.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and
adjusting tools are removed.
Store unused equipment in a dry, locked place out of the
reach of children.

Electrical safety

Design of the connection cable according to IEC 60245
(H 07 RN-F) with a core cross-profile section of at least
- 1.5 mm² for cable lengths up to 25 m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power;
the function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with
this material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Protect yourself against electric shocks. Avoid touching
earthed parts with your body (e.g. pipes, heating
apparatus, cookers, fridges etc.).
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points. Local
regulations – especially regarding protective measures –
must be observed.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer service
points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
12