Publicité
Liens rapides
Installation
Instructions
Questions? In the U.S., call 800.GE.CARES (800.432.2737)
In Canada, call 1.800.561.3344
BEFORE YOU BEGIN
❒
Read these instructions completely and carefully.
IMPORTANT –
•
IMPORTANT –
•
Note to Installer –
•
Consumer.
Note to Consumer –
•
• For easier installation and personal safety, we recommend that two people
install this microwave oven.
WARNING
grounded 3-hole, 120V receptacle as required by the National Electrical Code
or the Canadian Electrical Code.
FOR YOUR SAFETY:
WARNING –
installation, switch power off at service panel and lock
the service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
TOOLS YOU WILL NEED
❒ Phillips screwdriver
❒ Pencil
❒ Awl or punch
❒ Level
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
or Visit our Website at:
Save these instructions for local inspector's use.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the
Keep these instructions for future reference.
—
This oven must be plugged into a properly
Before beginning the
❒ Drill with
7
⁄
" bit or #35
64
❒ Tape measure
❒ Scissors (optional)
.
Built-In Trim Kits
JX2027 and JX2030
or Visit our Website at:
GEAppliances.ca.
• Do not alter or modify any part of this kit or the oven.
• Unplug the microwave oven before attempting installation of this kit.
• Skill level – Installation of this appliance requires basic mechanical and
electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is UL/CSA listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.
• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC, JEB1860SMSS, PEB206CDNBB, PEB206CSNSS,
PEB206CDNWW, JEB186CDNWW, JEB186CDNBB and JEB186CSNSS.
PARTS INCLUDED
PART
NOTE: This kit has extra screws to prevent the technician from spending extra
time locating a replacement screw in case they lose one during installation.
1
ge.com.
QUANTITY
❒
Trim Frame
❒
Bottom Duct
❒
Side Duct
❒
4 mm x 12 mm
Round-Head Screws (21 required
for installation)
❒
4 mm x 14 mm
Flat-Head Screws
(4 required for
installation)
❒
Anti-Tip Brace
❒
Anti-Tip Bracket
❒
Upper Duct
❒
Top Bracket
❒
Bottom Bracket
❒
Templates
1
1
1
23
6
1
1
1
1
1
2
Publicité
Manuels Connexes pour GE JX2027
Sommaire des Matières pour GE JX2027
- Page 1 • Product failure due to improper installation is not covered under the Warranty. Keep these instructions for future reference. • This kit is UL/CSA listed for installation alone or over any GE/GE Profile • For easier installation and personal safety, we recommend that two people single electric wall oven.
-
Page 2: Installation Instructions
Installation Instructions ❒ CUTOUT DIMENSIONS ❒ INSTALL THE ANTI-TIP BRACE Draw a line on the cutout floor at the center of the Models 27″ 30″ cutout, and extend the line 1/2″ down the face of Height ⁄ ″ ⁄ ″ the cabinet. - Page 3 Installation Instructions ❒ ❒ INSTALL ANTI-TIP BRACKET AND INSTALL SIDE DUCT AND UPPER BOTTOM DUCT DUCT (cont.) Set the microwave upright, being careful not to bend the front Disconnect the microwave oven before proceeding with the flange. Remove the one existing screw from the left side of the installation.
- Page 4 Installation Instructions ❒ ❒ CHECK LEVELING INSTALL THE TRIM FRAME Place the trim frame over the microwave oven with the Check the leveling by placing a level at the front and sides of the curved edge at the top. microwave. It may be necessary to Press the trim frame into the opening until all sides snap add wood shims under the bottom into place.