Annovi Reverberi BLUE CLEAN 1435 Mode D'emploi page 7

12 English
4 GENERAL INFORMATION (FIG.1)/PAGE 3
EN
4.1 Use of the manual
The manual forms an integral part of the appliance and should be
kept for future reference. Please read it carefully before installing/
using the unit. If the appliance is sold, the seller must pass on this
manual to the new owner along with the appliance.
4.2 Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
4.2.1 Documentation supplied with the appliance
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
A4 Warranty regulations
A5 Engine use and maintenance manual
4.3 Disposing of packaging
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
5 TECHNICAL INFORMATION (FIG.1)/PAGE 3
5.1 Envisaged use
This appliance has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc., to remove stubborn dirt
using clean water and biodegradable chemical detergents.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Intake water temperature: see data plate on the appliance.
- Intake water pressure: min. 0.1 MPa - max. 1 MPa.
- Operating ambient temperature: above 0°C.
The appliance is compliant with the IEC 60335-1 and IEC 60335-2-79
standards.
5.2 Operator
The symbol illustrated in fig. 1 identifies the appliance's intended
operator (professional or non-professional).
5.3 Main components
B1 - Internal combustion engine
B2 - Reduction gearbox (where fitted)
B3 - Pump
B4 - Gun with safety catch
B5 - Lance
B6 - High pressure hose
B7 - Oil caps (on models with this feature)
B8 - Nozzles
B9 - Detergent tank (on models with this feature)
B10 - Hose tail with filter
5.3.1 Accessories (if included in the supply package – see fig.1)
C1
Nozzle cleaning tool
C2
Rotating nozzle kit
5.4 Safety devices
Warning - danger!
Do not tamper with or adjust the safety valve setting.
- Safety valve and/or pressure limiting valve.
The safety valve is also a pressure limiting valve. When the gun
trigger is released, the valve opens and the water recirculates
through the pump inlet or is discharged onto the ground.
- Thermostat valve (D1 where fitted) If the water temperature
exceeds the temperature set by the manufacturer, the thermostat
valve discharges the hot water and draws in an amount of cold
water equal to the amount of water discharged, until the correct
temperature is restored.
- Safety catch (D): prevents accidental spraying of water.
93735_ARBC_Termik_1435 1440 1444 1445 1450.indb 12
6.1
6.2
6.3
6.4
6.5
C3
Handle
C4
Screws
6 INSTALLATION (FIG.2)/PAGE 4
Assembly
Warning - danger!
Remove the spark plug connector prior to performing
any work on the device.
The assembly sequence is illustrated in fig.2.
Fitting the pressure release caps
To prevent oil leaks, the appliance is delivered with the oil intakes
sealed with red caps which must be replaced with the pressure
release caps supplied.
Fitting the rotating nozzle
(For models with this feature).
The rotating nozzle kit delivers greater washing power.
Use of the rotating nozzle may cause a reduction in pressure of
25% compared to the pressure obtained with the adjustable nozzle.
However, the rotating nozzle kit delivers greater washing power due
to the rotation of the water jet.
Motor
Warning - danger!
Follow the instructions given in the section "Safety Notes"!
6.4.1 Read the operating instructions of the engine manufac-
turer before start-up and follow the safety instructions
carefully.
Check oil level of the engine. Do not operate the appliance
if the oil level has fallen below "MIN". If required, top up
oil carefully.
Fill the fuel tank with unleaded petrol. Do not use 2-speed
mixture.
Water supply connection
Warning - danger!
Only clean or filtered water should be supplied to
the appliance. The flow rate of the water inlet tap should be
equal to the pump flow rate.
Place the appliance as close to the water supply system as possible.
6.5.1 Connection points
l Water outlet (OUTLET)
n Water inlet with filter (INLET)
6.5.2 Connection to the mains water supply
The appliance may only be connected directly to the
mains drinking water supply if the supply hose is fitted
with a backflow preventer valve as per current regulations
in force. Make sure that the hose is at least Ø 13 mm, that
it is reinforced and that it is not more than 25 m long.
6.5.3 Suction of water from open containers
1) Screw the inlet hose with filter to the water INLET and
insert it down to the bottom of the container.
2) Vent the air from the appliance:
a) Unscrew the lance.
b) Start the appliance and keep the gun open until there
are no air bubbles in the water flowing out.
3) Switch the appliance off and screw the lance back on.
N.B.: the maximum suction height is 0.5 m. The suction
hose should be filled before use.
(on models with this feature)
17/6/14 下午4:16