M-Audio BASS TRAVELER Mode D'emploi

Technical Specifications
Maximum Output Power: Approximately 250 mW (16 Ω)
Maximum Drive Ability: 16–150Ω
Signal-to-Noise Ratio: > 90 dB (A-weighted)
Connections: 2 1/8" (3.5 mm) TRRS outputs; 1 1/8" (3.5 mm) TRRS input;
1 micro-USB port
Power: Internal lithium-polymer battery with 8-hour capacity
Dimensions
(width x depth x height)
Weight: 0.07 lbs. (1.12 oz.) / 0.03 kg (30 g)
Warnings:
• Excessive sound pressure (high volumes) from headphones can cause
hearing loss.
• To reduce the risk of fire or electrical shock, do not expose this product to
rain, liquids, or moisture. Electrical equipment should never be kept or
stored in damp environments. Do not expose this product to dripping or
splashing, and do not place objects filled with liquids on it.
• Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
Specifications are subject to change without notice.
User Guide (English)
For more information about this product (system requirements,
compatibility information, etc.), product registration, or product support,
visit m-audio.com.
For safety and warranty information, visit m-audio.com/warranty.
Package Contents: Bass Traveler, micro-USB cable, 1/8" (3.5 mm)
TRRS connector cable, User Guide.
Quick Start:
Items not listed in Package Contents are sold separately.
Important: Charge Bass Traveler for at least 2 hours before using it for
the first time.
1. Make sure Bass Traveler is charged and powered off (the Off/Volume
knob should be in the minimum position).
2. Use the included 1/8" (3.5 mm) cable to connect your audio source to
Bass Traveler's input.
3. Connect your 1/8" (3.5 mm) headphones to the output/outputs.
4. Turn the Off/Volume knob clockwise until it "clicks" on. The battery
indicator will be lit blue.
5. Play your audio source, and turn the Off/Volume knob to adjust the
volume of the headphones.
6. Optional: To add more equalization (EQ) to the audio in the
headphones, set the Boost switch to the desired setting.
Guía del usuario (Español)
Para más información acerca de este producto (requisitos de sistema,
información de compatibilidad, etc.), registro o soporte del producto,
visite m-audio.com. Para información sobre la seguridad y la
garantía, visite m-audio.com/warranty.
Contenido del paquete: Bass Traveler, cable micro-USB, cable
conector TRRS de 3,5mm (1/8 pulg.), guía del usuario
Inicio rápido:
Los elementos que no se enumeran en Contenido del paquete se
venden por separado.
Importante: Cargue el Bass Traveler durante al menos 2 horas antes de
utilizarlo por primera vez.
1. Asegúrese de que el Bass Traveler esté cargado y apagado (la perilla
Off/Volume (Apagado/volumen) debería estar en la posición mínima).
2. Utilice el cable de 3,5mm (1/8 pulg.) incluido para conectar su fuente
de audio a la entrada del Bass Traveler.
3. Conecte a la(s) salida/salidas sus auriculares de 3,5mm (1/8 pulg.).
4. Gire la perilla Off/Volume en sentido horario hasta que se escuche un
"clic". El indicador de la batería se iluminará de color azul.
5. Reproduzca su fuente de audio y apague la perilla Off/Volume para
ajustar el volumen de los auriculares.
6. Opcional: Para agregar más ecualización (EQ) al audio en los
auriculares, ajuste el interruptor Boost (Refuerzo) a la opción deseada.
: 1.84" x 1.80" x 0.60" / 46.9 x 45.7 x 15.2 mm
Safety & Compliance Notices:
that changes or modifications not expressly approved by the part responsible for compliance could void
the user's authority to operate the equipment. This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
(a) Reorient or relocate the receiving antenna; (b) move this unit; (c) increase the separation between the
equipment and receiver; (d) connect the equipment into an outlet on a circuit different from that to which
the receiver is connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where
appropriate; (f) consult the dealer or an experienced radio/television technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. End users must follow the specific operating instructions for
satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. For best audio quality, avoid using this device in a high RF-
radiated environment. RSS Statement for Canadian models: This device complies with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device This unit does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the radio interference regulations of the
Canadian Department of Communications.
ESD/EFT Warning: This unit may contain a microcomputer for signal processing and control
functions. In very rare situations, severe interference, noise from an external source, or static
electricity may cause it to lock up. In the unlikely event that this should happen, turn off the unit,
wait at least five seconds, and then turn it back on again. In an environment with radio frequency
interference, the unit may malfunction and resume normal operation after removal of the interference.
Correct Disposal of This Product: This marking indicates that this product should not be
disposed with other household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used device, please
use the return and collection systems or contact the retailer where the product was
v1.3
purchased. They can take this product for environmentally safe recycling.
Features:
1. Off/Volume: Turn this knob to adjust the
volume of the outputs. The knob's
minimum position is off.
2. Battery Indicator: This light indicates
Bass Traveler's current power status: on,
charging its battery, or low on battery
power.
3. Charging Port: Use the included micro-
USB cable to connect this micro-USB
port to a USB port on your computer
(powered on). Alternatively, connect it to
a USB power adapter (sold separately)
connected to a power outlet.
4. Input: Connect your audio source to this
1/8" (3.5 mm) TRRS input.
5. Outputs: Connect your 1/8" (3.5 mm)
headphones to these outputs.
6. Boost: Set this switch to a desired setting.
The Flat setting applies no equalization
(EQ). M applies a slight boost in EQ. H
applies the maximum amount of EQ.
Trademarks and Licenses
registered in the U.S. and other countries. All other product or company names are
trademarks or registered trademarks of their respective owners.
Características:
1. Apagado/volumen: Gire esta perilla para
ajustar el volumen de las salidas. La
posición mínima de esta perilla es
apagado.
2. Indicador de la batería: Esta luz indica
el estado actual de la batería del Bass
Traveler: encendida, cargando batería, o
batería agotándose.
3. Puerto de carga: Utilice el cable micro-
USB incluido para conectar este puerto
micro-USB a un puerto USB en su
ordenador (encendido). Como alternativa,
conéctelo a un adaptador de corriente
USB (que se vende por separado)
conectado a una toma de corriente.
4. Entrada: Conecte su fuente de audio a
esta entrada TRRS de 3,5mm (1/8 pulg.).
5. Salidas: Conecte a estas salidas sus
auriculares de 3,5mm (1/8 pulg.).
6. Refuerzo: Ajuste este interruptor a la
opción deseada. El ajuste Flat (Plano) no
aplica ninguna ecualización (EQ). M aplica
un ligero refuerzo al ecualizador. H aplica
la máxima cantidad de ecualización.
Notice Concerning FCC Regulations: You are cautioned
1
2
6 4
: M-Audio is a trademark of inMusic Brands, Inc.,
1
2
6 4
5 5
3
5 5
3