Economic Operating Mode; Off Mode - Haverland RC 4 ECO Manuel D'instructions

1º
Access the Functions menu by pressing the OK key for at least two
seconds. The upper section of the screen will display all the heater functions.
2º
Use the keys to position the function selector cursor
comfort symbol (Note 1).
Note 1
3º
The screen displays the following information:
- The function selector is set to "Comfort" mode.
- The currently programmed comfort temperature (22 ºC).
- The current time and day of the week (8:00 am and Wednesday
3).
4º
Press OK to enter the "Comfort" operating
mode.
5º
We are now going to modify the previously
programmed comfort temperature from 22 to
23 ºC by pressing the "+" key until 23 ºC is dis-
played.
6º
Enter the new data by pressing OK.
7º
Automatically, within a few seconds, the current room temperature (20 ºC)
will be displayed, and since this is less than that set, the heater will be auto-
matically switched on.
"The heater is
operating"
Room tempera-
ture: 20ºC
8º
You have just modified the comfort temperature from 22 to 23 ºC. The
flame indicator will remain displayed until the temperature reaches the 23 ºC
we have programmed
Important note: The comfort temperature you have just set will be
employed as a reference for when you use the "Automatic" mode. WHE-
NEVER YOU WISH TO DISPLAY THE PROGRAMMED COMFORT TEMPE-
RATURE SIMPLY PRESS THE "OK" KEY.
10.2 ECONOMIC temperature operating mode:
The "Economic" temperature mode is accessed in the following way:
1º
Press the "OK" key for at least two seconds until the Functions menu is
displayed.
2º
Use the keys to set the functions selector
symbol (Note 2).
S S
3º
The screen will display the following information:
- The functions selector is located on the "Economic" mode.
- The currently programmed economic temperature (17 ºC).
- The current time and day of the week (8:00 am and Wednesday
"3").
4º
Press "OK" enter the "Economy" operating mode.
5º
We are now going to change the economy
over the
temperature from 17 ºC (which was programmed
previously) to 16 ºC.
6º
Use the "-" key to reduce the temperature to
16 ºC.
7º
Press "OK" to accept this new value.
8º
Automatically within a few seconds, the scre-
en will display the room temperature (18 ºC) and
the heater will switch on if the room temperature
is less than 16 ºC
9º
You have just modified the economy tempera-
ture from 17 to 16 ºC.
In this case, the heater is not switched on becau-
se the room temperature is at 18 ºC and this is
higher than the programmed economy temperature of 16 ºC. The flame sym-
bol will not, therefore, be displayed aty this time, however, it will be seen if the
room temperature falls below 16 ºC.
Important note: The economy temperature you have just programmed
will be taken as reference in the case of employing the "Automatic" ope-
rating mode. WHENEVER YOU WISH TO DISPLAY THE PROGRAMMED
ECONOMY TEMPERATURE SIMPLY PRESS THE "OK" KEY.

10.3 OFF mode:

We are now going to explain how to switch your heater off. This is achieved by
accessing the "Off" function.
1º
Access the Functions menu by pressing the "OK" key for at least two
seconds. The heater's functions will be displayed in the upper section of the
screen.
2º
Use the
the "Off" symbol (Note 3).
3º
Press "OK" to enter the "Off" mode.
The timer-thermostat will switch off first followed by the pilot lamp a few
seconds later.
The screen will continue to display the time and the day of the week.
over the "Economy"
Note 2 When switched off in this manner, the heater will maintain all programming in
its memory and the clock will continue to operate and be displayed.
IMPORTANT NOTE:
In order to switch the heater on again, press the "OK" key for at least two
seconds and then select the desired operating mode.
IMPORTANT NOTE:
If you leave the appliance disconnected from the wall socket for more
than approximately 24 hours, the current time and day of the week
will have to be reprogrammed. All other programming will be kept.
PAG. 40
keys to position the function selector cursor
Note 3
S S
over
EN