Vibration Information; Vibration Level; Battery Charging - IKEA FIXA Traduction Des Instructions Originales

Unintentional actuation of the On/Off
switch can lead to injuries.
Protect the power tool against heat,
e. g., against continuous intense
sunlight, fire, water, and moisture.
Danger of explosion.
In case of damage and improper use of
the battery, vapours may be emitted.
Provide for fresh air and seek medical
help in case of complaints. The vapours
can irritate the respiratory system.
Safety Warnings for battery chargers
For indoor use only.
Double insulated.
Keep the battery charger away from
rain or moisture. Penetration of water in
the battery charger increases the risk of an
electric shock.
Do not charge other batteries. The
battery charger is suitable only for
charging the batteries that were supplied
with your power tool. Otherwise there is
danger of fire and explosion.
Keep the battery charger clean.
Contamination can lead to danger of an
electric shock.
Before each use, check the battery
charger, cable and plug. If damage
is detected, do not use the battery
charger. Never open the battery
charger yourself. Have repairs
performed only by a qualified
technician. Damaged battery chargers,
cables and plugs increase the risk of an
electric shock.
Do not operate the battery charger
on easily inflammable surfaces (e. g.,
paper, textiles, etc.) or surroundings.
The heating of the battery charger during
the charging process can pose a fire
hazard.
Children should be supervised to
ensure that they do not play with the
battery charger.
Products sold in GB only: Your product is
fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to
BS 1362). If the plug is not suitable for
your socket outlets, it should be cut off
and an appropriate plug fitted in its place
by an authorised customer service agent.
The replacement plug should have the
same fuse rating as the original plug. The
severed plug must be disposed of to avoid
a possible shock hazard and should never
be inserted into a mains socket elsewhere.
Products sold in AUS only: Use a residual
current device (RCD) with a rated residual
current of 30 mA or less.

VIBRATION INFORMATION

Vibration level

The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given
in UL 60745 / CSA C22.2 No. 60745. It
may be used to compare one tool with
another and as a preliminary assessment
of exposure to vibration when using the
tool for the applications mentioned in
this manual. However, using the tool for
different applications, or with different
8
or poorly maintained accessories, may
significantly increase the exposure level.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off or
when it is running but not actually doing
the job, as this may significantly reduce
the exposure level over the total working
period.
Protect yourself against the effects of
vibration by maintaining the tool and its
accessories, keeping your hands warm,
and organizing your work patterns.
ASSEMBLY
Before any work on the machine
(e. g., maintenance, tool change,
etc.) as well as during transport
and storage, set the rota tional
direction switch to the centre posi-
tion. Unintentional actuation of the On/Off
switch can lead to injuries.

Battery charging

Charging your hammer drill
When the charger is connected to the
electricity supply, the red diode on the
hammer drill lights up. The diode lights up
while the battery is being charged (13).
Under normal conditions of use the
hammer drill can be recharged several
hundred times.
ATTENTION! The recharging process
generates heat in the battery.
Note: The battery that is supplied with
the hammer drill has been charged for test
purposes only and must be fully charged
before first time use.
First read the safety instructions and then
follow the loading instructions. Insert the
charge connector (15) into the socket
(13) in the hammer drill. Then connect
the charger's transformer to the electricity
supply.
Make sure that there are no knots or sharp
bends in the cable.
The charger's transformer and the battery
have been designed to be used together.
NEVER use this charger to recharge
cordless tools or batteries from other
manufacturers. The battery will gradually
lose its charge over a period of time, even
if the tool is not used.
The lithium-ion battery is protected against
deep discharging by the "Electronic Cell
Protection (ECP)". When the battery is
empty, the machine is switched off by
means of a protective circuit: The inserted
tool no longer rotates.
WARNING! Do not continue
to press the On/Off switch after the
machine has been automatically
switched off. The battery can be
damaged.
WARNING! Recharge the battery
on a non-flammable surface. Do not
recharge the battery for more than
eight hours. The red diode will turn green
when the battery has been fully loaded.
9