Product Identification - turck TX707 Mode D'emploi

TX707/TX710/TX715/TX721
EN
Quick Start Guide
HMI – TX707/TX710/TX715/TX721
For Your Safety
Intended use
The HMIs (Human Machine Interfaces) of the TX700 family are used to control,
operate and monitor machine processes.
The devices are suitable for use in Zone 2 and Zone 22.
The devices may only be used as described in these instructions. Any other use
is not in accordance with the intended use; Turck accepts no liability for any
resulting damage.
General safety instructions
■
The device may only be assembled, installed, operated, parameterized and
maintained by professionally-trained personnel.
■
The device only meets the EMC requirements for industrial areas and is not
suitable for use in residential areas.
■
The device may only be used in accordance with applicable national and
international regulations, standards and laws.
Notes on explosion protection
■
Observe national and international regulations for explosion protection.
■
When operating the device in a hazardous area, the user must also have a
working knowledge of explosion protection (EN 60079-14, etc.).
■
Only use the device within the permitted operating and ambient conditions
(see Certification data and conditions resulting from the Ex-approval).
■
This device, with the exception of the front display, is an open device and
must be installed in a housing suitable for the environment, so that the inner
part of the device is only accessible by means of a tool.
■
Do not disconnect devices in an ignitable atmosphere when energized.
■
Do not open the device when energized.
■
Do not remove Ethernet connections, USB devices and SD cards in an ignit-
able atmosphere.
■
Do not remove the battery in an ignitable atmosphere.
■
Switch-off the device before replacing or wiring extension modules.
Note on explosion protection (USA and Canada only)
■
The devices are suitable for the use in Class 1, Division 2, groups A, B, C and D
(hazardous locations and non-hazardous locations).
■
The Power, input and output (I/O) wiring has to be done in accordance with
Class I, Division 2 and in accordance with the authority having jurisdictions.
For U.S. in accordance with Article 501.10 (B) of the National Electrical Code,
NFPA 70 and for Canada in accordance with Section 18-1J2 of Canadian
Electrical Code.
■
Use only components that meet Class 1, Division 2 certification.
Conditions resulting from ATEX and IEC Ex approval for use in Zone 2/Zone 22
■
The equipment shall only be used in an area of not more than pollution
degree 2, as defined in IEC/EN 60664-1.
■
When used in Zone 22: Install the device in a housing of protection class IP6x
approved for dust areas.
■
The equipment shall be installed in an enclosure that provides a degree of
protection not less than IP54 in accordance with IEC/EN 60079-15.
■
Only disconnect and connect non-intrinsically safe circuits when no voltage
is applied.

Product identification

Type label
See fig. 8 (example)
Imprint
Type designation
Ident no.
Year/week of production
Serial number
Internal version ID of the product
Manufacturer address
Product Description
Device overview
See fig. 1
A B
TX707 187 mm/ 147 mm/
7.36" 5.79"
TX710 282 mm/ 197 mm/
11.10" 7.80"
TX715 422 mm/ 267 mm/
16.60" 10.50"
TX721 552 mm/ 347 mm/
21.73" 13.66"
Functions and Operating Modes
The HMIs (Human Machine Interfaces) of the TX700 series combine control,
operation and monitoring in a full-scope control thanks to the CODESYS V3
PLC with integrated visualization. The CODESYS 3 control of the TX700 has the
functions PROFINET controller, EtherNet/IP™ scanner and Modbus TCP as well as
Modbus RTU master. Additionally the devices of the TX700 family can be used as
Modbus TCP as well as Modbus RTU slave.
Additional functions
■
Ethernet TCP/IP or UDP/IP communication
■
OPC-UA server and client
■
Serial communication via RS232, RS485 and RS422
Mounting
See fig. 2 and 3
A = TX7...
B = cut-out
Mount the device as follows:
Screw each fixing screw until the bezel corner gets in contact with the panel.
➤
The maximum tightening torque is 1.3 Nm.
Select a mounting location so that the device is not exposed to direct sun-
➤
light.
Do not cover the ventilation slots in the device.
➤
TX... Number of fixing brackets supplied
TX707 4
TX710 9
TX715 12
TX721 14
Mounting the device in Zone 2/Zone 22
DANGER
Explosive atmosphere
Explosion hazard due to ignitable sparks
For use in Zone 2 and Zone 22
Only mount the device if no explosive atmosphere is present.
➤
For use in Zone 2: Mount the device in a Ex-e housing according to EN
➤
60079-0 with a protection class of at least IP54.
For use in Zone 22: Install the device in a housing of protection class IP6x
➤
approved for dust areas.
When mounting the device in the housing, ensure that the permissible op-
➤
erating temperature of the device is not exceeded, even under unfavorable
ambient conditions.
© Hans Turck GmbH & Co. KG | 1000002510 2020-03 DE EN FR
Meaning
TX707
100002030
2003
AA 000 12MF 123456789AA
V121112A09800157
Hans Turck GmbH & Co. KG
Witzlebenstr. 7
D-45472 Muelheim a. d. Ruhr
www.turck.com
C D E
176 mm/ 136 mm/ 47 mm/
6.90" 5.35" 1.85"
271 mm/ 186 mm/ 56 mm/
10.67" 7.32" 2.20"
411 mm/ 256 mm/ 56 mm/
16.18" 10.00" 2.20"
541 mm/ 336 mm/ 56 mm/
21.30" 13.22" 2.20"
F
8 mm/
0.31"
8 mm/
0.31"
8 mm/
0.31"
8 mm/
0.31"