Publicité
10. 360° Tangle-Free
Swivel Cord
11. See-Through Water Reservoir
12. Self-Clean Button
13. MicroGlide™ Soleplate
(Model 4265-33 only)
Stainless Steel Soleplate
(Model 4267-33 only)
14. Maximum Fill Line
15. Storage Strip
Indicator
®
(Model 4265-33 only)
t
f
W
R
o
Ill the
ateR
eseRvoIR
1. M ake sure the iron is unplugged. Set the Steam Selection Slide to OFF (Dry).
2. S lide open the Water Fill Hole Cover.
3. F ill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum
fill line.
Warning: T o prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and
steam can cause injuries.
s
f
s
electIng
aBRIc
ettIngs
To select a fabric setting, (Figure A) press the ( - + ) Fabric Select button until the desired fabric is highlighted. The
Wait light will glow red while the iron heats up.
The light will then change to green (Ready) when the iron is ready to use.
d
I
RY
RonIng
1. M ake sure the Steam Selection Slide is turned to the OFF (Dry) setting.
2. Plug the cord into a 120-Volt AC outlet.
3. Select Fabric Setting.
Note: While the Steam Selection Slide is turned to the OFF (Dry) setting, you may still use the SHOT OF STEAM
®
feature or SPRAY MIST
feature. Please make sure the water reservoir is at least 1/4 full of water.
Tip: Refer to the Ironing Guide for the recommended setting for your fabric.
s
I
team
RonIng
1. Follow the instructions for "To Fill the Water Reservoir".
2. Plug the cord into a 120-Volt AC outlet.
3. S elect Fabric Setting.
4. A llow the iron to heat for 2 minutes, and then turn the Steam Selection Slide
to the appropriate setting.
Tip: Refer to the Ironing Guide for the recommended setting for your fabric.
Important: When not ironing, always set the Steam Selection Slide to OFF (Dry).
u
sIng the
®
s
m
f
pRaY
Ist
eatuRe
The Spray Mist
®
feature is a powerful water spray mist that dampens the fabric
to aid in removing wrinkles from heavy fabrics and for setting creases.
t
s
m
f
®
o use the
pRaY
Ist
eatuRe
Press the Spray Mist
®
button firmly. Iron over the fabric to dry.
®
s
s
f
hot of
team
eatuRe
The Shot of Steam
®
feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use
this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water.
t
s
s
f
®
o use the
hot of
team
eatuRe
Place the iron on top of the wrinkle and press the Shot of Steam
I
'
s
f
Ron
s
pecIal
eatuRes
:
:
®
button each time you would like an extra burst of
13
14
15
®
11
12
WARNING: NEVER yank the power cord when unplu
This can damage the cord.
W
/R
l
aIt
eadY
Ight
Indicates when your iron reaches the desired temperature
illuminates. Once the iron heats up to the desired fabric s
(Ready). This occurs each time the fabric setting is change
Auto-Off is deactivated.
a
-c
s
ntI
alcIum
Ystem
The Anti-Calcium System is a permanent system located
from the water and reduces calcium build-up on the solep
m
g
™ s
(
IcRo
lIde
oleplate
model
Provides superior glide over Non-stick and Stainless Steel
d
-f
RIp
Ree
Produces steam without any dripping, spitting, or leaking
even at low temperatures.
s
s
I
®
(model 4265-33 only)
toRage
tRIp
ndIcatoR
The STORAGE STRIP
®
indicator is an easy way to see when
t
s
s
®
o use the
toRage
tRIp
IndIcatoR
Turn iron on. In approximately 2 minutes, the STORAGE
that the iron is too hot to store. When the iron is turned off,
®
STORAGE STRIP
indicator to turn from red to black, ind
Caution: The STORAGE STRIP
®
indicator should only be
stored with care.
t
o
Y
I
uRnIng
ff
ouR
Ron
1. Unplug the iron from the power source.
WARNING: NEVER yank the power cord when unplu
s
Y
I
toRIng
ouR
Ron
1. Allow the iron to cool. (Model 4265-33 only: Wait
original black color, indicating that the iron is cool e
2. I f you do not use your iron on a daily basis, empty t
do so, unplug the iron, turn the iron upside down, o
hole. Shake the iron gently to remove trapped water
3. L oosely loop the power cord around the heel rest an
Important: Wrapping the cord around the iron too tightl
Tip: When not ironing, always set the Steam Selection Sli
m
c
s
leanIng the
oleplate
Clean the soleplate if starch or other residue accumulate.
Toggle up to
desired fabric and
wait for red light
to turn green.
Faites basculer
au textile voulu
puis attendez que
le voyant rouge
tourne au vert.
4265-33
)
onlY
:
c
Y
aRIng foR
ou
Y
aIntaInIng
ou
Publicité
