Operation; Applications; Fueling And Refueling The Trimmer - Toro 51954 Manuel De L'utilisateur

Operation

WARNING:
Do not allow familiarity with this product to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict
serious injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and other
possible serious injuries.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool.
The use of attachments or accessories not rec-
ommended can result in serious personal injury.

Applications

Use this product for the following applications:
■
Cutting grass, weeds, and light undergrowth
■
Edging along sidewalks and driveways

Fueling and Refueling the Trimmer

WARNING:
Gasoline and its vapors are highly flammable
and explosive. To prevent serious personal
injury and property damage, handle it with care.
Keep away from ignition sources and open
flames, handle outdoors only, do not smoke and
wipe up spills immediately.
Fuel Mixture
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded
gasoline and 2-cycle engine lubricant in a clean 1 gallon
container approved for gasoline.
Recommended fuel: This engine is certified to operate on
unleaded gasoline intended for automotive use.
Mix a high quality 2-cycle engine lubricant at 2.6 oz. per
gallon (US).
Do not use automotive lubricant or 2-cycle outboard
lubricant.
DO NOT mix quantities larger than usable in a 30 day
period.
14
HIGH qUALITY 2-CYCLE ENGINE LUBRICANT
Gasoline
1 gallon (US)
1 liter
Filling Tank
■ Clean surface around fuel cap to prevent contamination.
■ Loosen fuel cap slowly by turning counterclockwise. Rest
the cap on a clean surface.
■ Carefully pour fuel into the tank. Avoid spillage.
■ Prior to replacing the fuel cap, clean and inspect the
gasket.
■ Immediately replace fuel cap and hand tighten by turning
clockwise. Wipe up any fuel spillage.
■ Move at least 30 ft. away from refueling area before starting
the product.
note: It is normal for smoke to be emitted from a new
engine after first use.
WARNING:
Always shut off engine before fueling. Never
add fuel to a machine with a running or hot
engine. Move at least 30 ft. from refueling site
before starting engine. Do not smoke and stay
away from open flames and sparks. Failure to
safely handle fuel could result in serious per-
sonal injury.
Oxygenated Fuels
Some conventional gasolines are blended with alcohol or an
ether compound. These gasolines are collectively referred to
as oxygenated fuels. To meet clean air standards, some areas
of the United States and Canada use oxygenated fuels to
help reduce emissions.
If using an oxygenated fuel, make sure it is unleaded and
meets the minimum octane rating requirements. Before
using an oxygenated fuel, try to confirm the fuel's contents.
Some states/provinces require this information to be posted
on the pump. The following are the EPA approved percent-
ages of oxygenates:
ethanol (ethyl or grain alcohol) 10% by volume. You
may use gasoline containing up to 10% ethanol by volume.
Gasoline containing ethanol may be marketed under the
name "Gasohol." Do not use e85 fuel.
Mtbe (methyl tertiary butyl ether) 15% by volume. You
may use gasoline containing up to 15% MTBE by volume.
Methanol (methyl or wood alcohol) 5% by volume. You
may use gasoline containing up to 5% methanol by volume
as long as it also contains cosolvents and corrosion inhibi-
tors to protect the fuel system. Gasoline containing more
than 5% methanol by volume may cause starting and/or
lubricant
2.6 oz.
20 cc (20 ml)
Operation