Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Insert the shank of the saw blade into the blade holder
(12) as far as it will go.
Release the blade clamp (11).
Saw blade storage (fig. C)
Saw blades (10) can be stored in the storage compartment
(4) located on the side of the tool.
Open the cover of the saw blade storage
compartment (4) by holding the tab on the top of the
cover and pulling it outward.
The blades are retained in the compartment by a
magnetic strip. To remove a blade, press down on one
end of the blade to raise the other end, and remove.
Close the cover of the saw blade storage compartment
(4) and make sure that it is latched closed.
Warning! Close the storage compartment door securely
before operating the saw.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor (13) is required to connect a vacuum cleaner or
dust extractor to the tool.
Push the adaptor (13) into the dust extraction outlet (6).
Connect the vacuum cleaner hose (14) to the adaptor
(13).
Cut line blower (fig. E)
To aid visibility when cutting, your jigsaw is equipped
with a cut line blower (15) which will keep the work area
clear of dust as you saw.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Adjusting the shoe plate for bevel cuts (fig. F and G)
Warning! Never use the tool when the shoe plate is loose or
removed.
The shoe plate (7) can be set to a left or right bevel angle of
up to 45°.
Pull the shoe plate locking lever (5) outwards to unlock
the shoe plate (7) from the 0 deg position.
Pull the shoe plate (7) forward and set the required
bevel 15°, 30° and 45° indicated in the bevel angle
window.
Push the shoe plate locking lever (5) back towards the
saw to lock the shoe plate (7).
To reset the shoe plate (7) for straight cuts:
Pull the shoe plate locking lever (5) outwards to unlock
the shoe plate (7).
Set the shoe plate (7) to an angle of 0° and push the
shoe plate backwards.
Push the shoe plate locking lever (5) back towards the
saw to lock the shoe plate (7).
Setting the pendulum stroke (fig. H)
Set the pendulum stroke selector (9) to the required
position.
Position 0: metal and aluminium and sheet metal.
Position I: for laminates, hard wood, work tops.
Position II: for plywood and PVC/Plastics.
Position III: for soft wood and fast cutting.
Variable speed control
Set the variable speed control knob (1) to the required
speed range.
Use a high speed for wood, medium speed for
aluminium and PVC and low speed for metals other
than aluminium.
Switching on and off
To switch the tool on, press the on/off switch (2).
To switch the tool off, release the on/off switch (2).
For continuous operation, press the lock-on button (3)
and release the on/off switch (2).
To switch the tool off when in continuous operation,
press the on/off switch (2) and release it.
Sawing
Hold the tool firmly with both hands while cutting.
The shoe plate (7) should be held firmly against the material
being cut. This will help prevent the saw from jumping,
reduce vibration and minimise blade breakage.
Let the blade run freely for a few seconds before starting
the cut.
Apply only a gentle pressure to the tool while performing
the cut.
ENGLISH
9
Publicité
Table des Matières
