Proper Use; Technical Data - HERKULES HFS3500-Pro Traduction Des Instructions D'origine

• Please quote our article numbers as well as type
and production year in all your orders.

4. Proper use

The machine corresponds to the valid EU Ma-
chine Directive
• Before starting work, all the protection- and safety
devices must be installed on the machine.
• The machine is designed for operation by one per-
son. The operator will be responsible for the pres-
ence of third persons in the work area.
• Observe all safety- and danger instructions on the
machine.
• Keep all safety and danger instructions near the
machine in complete and readable form.
• The machine with the offered tool and accesso-
ries is exclusively designed for the cutting of tile
and concrete blocks with a cutting height of up
to 110 mm. The cutting of metal and wood is not
permitted.
• The dimensions of the workpieces to be machined
should not exceed or fall below the specified max-
imum and minimum dimensions.
• Please use the machine only if it is in a technically
fault-free condition. Use It properly, conscious of
the involved safety and risk factors and giving due
consideration to the operating instructions manual!
Faults, especially those that can affect safety must
be rectified immediately!
• The safety-, workplace- and maintenance spec-
ifications of the manufacturer as well as the di-
mensions specified in the technical data must be
observed.
• The applicable accident prevention measures and
the other generally recognized technical safety
rules must be observed.
• The machine must be used, serviced or repaired
only by persons who are familiar with it and who
have been briefed about its risks. Arbitrary alter-
ations to the machine will make the liability of the
manufacturer for damages resulting there from null
and void.
• The machine may be used only with original ac-
cessories and original tools of the manufacturer.
Despite proper use, certain residual risk factors
cannot be eliminated fully. The following things can
occur, depending on the design and structure of the
machine:
• Intervention in the running diamond cutting disc.
• Contact with the diamond cutting disc in exposed
area.
• Ejection of work pieces and work piece compo-
nents.
• Ejection of a faulty diamond attachment in the cut-
ting disc.
• Hearing damage due to non-use of the required
hearing protection.
• Injuries to the eyes due to non-use of eye pro-
tection
Any use beyond the one specified will be treated
as improper. The manufacturer will not be liable for
damages resulting from such improper use; the risk
will be borne by the user alone.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.

5. Technical data

Production dimensions
L x W x H
Cutting table
Diamond cutting wheel
Hole
Speed
Weight
Max. cutting length
Max 90° cutting height
Max. 45° cutting
height
Motor
Power intake
Insulating material
class
Protection type
Technical changes reserved!
Noise characteristic values
Noise at the workplace can exceed 85 dB (A). In this
case, noise protection measures are necessary for
the user (wear hearing protection!).
Noise output level in dB
L idling / processing of L
WA WA
Noise pressure level at workplace in dB
L idling / processing of L
PA PA
to DIN EN ISO 3744; EN ISO 11201
Operation mode S6 40%, continuous operation peri-
odic duty. Identical duty cycles with a period at load
followed by a period at no load. Running time 10 min-
utes; duty cycle is 40% of the running time.
1200 x 600 x 1260 mm
530 x 430 mm
ø 350 mm
ø 25,4 mm
2800 1/min
72,3 kg
800 mm
110 mm
72 mm
230-240 V / 50 Hz
2000 W (S6 40%)
B
IP54
= 90/93 dB (A)
= 77/80 dB (A) according
GB | 25