Technical Specifications - Kärcher FC 3 Cordless Mode D'emploi

Masquer les pouces Voir aussi pour FC 3 Cordless:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 23
Formation of foam on the floor head and the
Note
Slight foam formation in the floor head during operation
is normal and does not impair functionality. Further
measures are only necessary when there is excessive
foam formation (e.g. streaks of foam on the floor).
Incorrect detergent or incorrect dosage.
 Use only KÄRCHER detergent and be sure to use
the correct dosage.
Device operation is based on the cleaning rollers re-
moving dirt. Dirt and detergent residues from floor cov-
erings collect in the waste water tank. This can lead to
foam formation under some circumstances.
 Remove all dirt and detergent residues from the
rollers using water.
Illustration
Illustration
Illustration
 In the event of excessive foam formation, add
FoamStop to the empty waste water tank before
starting cleaning. Please observe the dosage in-
structions on the bottle label.
Poor cleaning result
The rollers are dirty.
 Clean the rollers.
Rollers are not being sufficiently moistened.
 Moisten the rollers by moving back and forth over
the same position.
Incorrect detergent or incorrect dosage.
 Use only KÄRCHER detergent and be sure to use
the correct dosage.
Foreign detergents are present on the floor.
 Remove all detergent residues from the rollers us-
ing water.
 Clean the floor several times using the device and
clean rollers, without using detergent. This re-
moves detergent residues from the floor
Rollers do not turn
Rollers are blocked.
 Remove rollers and check if an object has become
stuck in the rollers.
 Check that the rollers are screwed in as far as they
will go onto the roller holder.
 Check that the floor head cover is correctly seated.
For this, remove the cover and then fit it back in
place.
Water vacuuming not optimum
Floor head cover not installed correctly
 Check that the floor head cover is correctly seated.
For this, remove the cover and then fit it back in
place.
The rollers are worn out.
 Replace the rollers.
Appliance is leaking waste water.
Waste water tank is overfilled.
 Empty the waste water tank right away.
Waste water tank does not fit properly in the appliance.
 Check that the floor head cover is firmly seated on
the waste water tank.
 Check that the waste water tank flaps are correctly
closed.
22
floor
Removing the handle from the basic unit
ATTENTION
Do not remove the handle from the basic unit once it has
been assembled.
The handle may only be removed from the basic unit if
the unit is sent out for service purposes.
Illustration
See illustration at the end of the operating instructions
 Insert screwdriver at a 90 degree angle in the small
opening at the rear side of the handle and remove
handle.
ATTENTION
Please ensure that the connection cable between the
basic unit and the handle are not damaged.

Technical specifications

Electrical connection
Voltage
Protection class
Device
Protective class
Charger protection class
Rated power of appliance
Nominal battery voltage
Battery type
Operating time with full charge
Charging time for empty battery
Charger initial voltage:
Output current, charger
Performance data
Roller revolutions per minute
Filling quantity
Fresh water tank
waste water tank
Dimensions
Weight (without accessories and
cleaning fluids)
Length
Width
Height
Cable length
Charger
Subject to technical modifications!
– 13
EN
100-240 V
1~50-60 Hz
IPX4
III
II
40 W
7,2 V
Li-Ion
20 min
4 h
9,5 V
0,6 A
500 rpm
360 ml
140 ml
2,4 kg
305 mm
226 mm
1220 mm
1800 mm

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Fc 3 cordless premium

Table des Matières