Maico DS 45 RC Guide Rapide page 2

Maico Elektroapparate Fabrik GmbH
Steinbeisstr. 20 • D-78056 Villingen-Schwenningen • Service.: 07720 694 447 • Fax: 07720 694 239 • e-mail: technik@maico.de • Internet: www.maico-ventilatoren.de
Installation and operating instructions
DS-RC Radio Switch
Part-no.: 0157.0363
1. General
1.1 Application
The radio transmission of the DS-RC radio switchs takes
place at the European harmonised frequency of 868.3 MHz.
They are particularly suitable for areas where no repairs are
required, such as renovations, retrofitting of electrical sy-
stems or offices with mobile walls. By pressing a button, con-
sumers can be switched wirelessly through receivers.
The radio switchs must be assigned to the receivers. There-
fore, refer to the receivers operating instructions. Every radio
switch can control an indefinite number of receivers.
Notes:
– The radio switchs function without batteries and are maintenance-free !
– Read through the operating instructions carefully before
putting the device into service.
1.3 Disposal of the device
The device must be disposed of in compliance with the laws and standards of the
country in which it is operated!
2. Safety
This device is only intended to be used for its stated application. Unauthorised conver-
sions, modifications or changes are not permissible! This device may not be used in
conjunction with other devices whose operation could present a hazard to persons,
animals or property.
The following must be observed:
• Prevailing statutes, standards and regulations.
• State-of-the-art technology at the time of installation.
• The device's operating instructions.
• Operating instructions can only cite general stipulations. These are to be viewed in
the context of a specific system.
3. Technical specifications
General data
Operating fequency 868.3 MHZ
Transmission power 10 mW
Modulation type (ASK Amplitude Shift Keying)
Cycles of operation min. 50,000
Operating temperature -25°C to +65°C in dry rooms
Relative humidity 0% to 95 %
Protection type IP20
Range in buildings
Masonry 20m (max. 3 walls)
Reinforced concrete 10m (max. 1 wall/ceiling)
Drywall/wood 30m (max. 5 walls)
Note:
The strength of the radio signal between sender and receiver decreases with incre-
asing distance. The visually unobstructed range is about 30 m in passageways and
100 m in open rooms. The range can be increased through the use of an repeater.
4. Structure and description
The radio switchs are to be completed with the combination frames of the according
switch programme. The combination frames have to be ordered separately!
DS 45 RC can be combined with following variations of the frame.
Manufacturer: Frame:
Berker: S1, B1, B3, B7 Glas, K1
Feller:
Edizio Due
Gira: E2, Standard55, Esprit, Event
Jung: A500, AS500, Aplus, A creation
Merten:
M-Smart, M-Arc, M-Plan
Peha:
Aura
Siemens:
Delta-Profil, Delta-Style, Delta-Miro, Delta-Vita, Delta-Line
In the delivery condition, the DS 45 RC is supplied with the Gira E2 frame
(pure white).
MBA DS 45 RC_02.17_th
GB
5. Mounting and commissioning
5.1 Mounting instructions
• Do not use outdoors (indoors only).
• Before assembly on rough surfaces create a flat surface. Unevenness may lead to
malfunction of the radio switch.
• Please consider the required installation position (
• NEVER mount the transmitter in a metal housing or in close proximity to
large metal objects. It is not recommended to mount it near the ground or on
the floor.
5.2 Mounting
a) Screws
• Retaining plates (2) shall be used as a template to mark the drill holes.
• Drill dowel holes of 5 mm.
• Fix the retaining plate with the screws. The latches of the retaining plate have
to be positioned for their installation as shown in the picture.
• Fit the radio switch (4 + 5), the frame (3) and the rockers (6) together and
press it on the retaining plate (2).
b) Glue:
• Fit the radio switch (4 + 5), the frame (3) and the rockers (6) together and
press it on the retaining plate (2).
• Use adhesive film (1) for the installation on flat, smooth surfaces. Glue the
adhesive film to the inverse side of the retaining plate.
• Glue the assembled radio switch to the desired location.
5.3 Commissioning
• Install the receiver unit PP 45 RC (only by an electrician).
• Assign the radio switch to the receiver.
• For detailed description use assembly and installation instructions from PP45
device.
6. Assignment of the keys
Key Duration
short < 1s.
short < 1s.
short < 1s.
short < 1s.
long 2s.
long 2s.
long 2s.
long 2s.
7. Troubleshooting & remedies
7.1 New system or existing system
• Check the immediate surroundings of the system for changes that might
cause malfunctions (e.g. previously moved metal cabinets, furniture or
walls).
• If transmitter / receiver operate at a closer distance, there either might be
interference or the system is used outside the transmission range.
• Placement of the transmitter at a more convenient location.
7.2 Radio signal range limitations
• Use of the radio switch/receiver in the vicinity of metal objects or materials with
metal components. Maintain a distance of at least 10 cm.
• Moist materials.
• Devices which emit high-frequency signals (e.g. audio and video systems,
computers, electronic ballasts in lightfixtures. Maintain a distance of at least 0.5 m.
7.3 Contact
Phone:........................ 07720 694 447
Fax:........................... 07720 694 239
Internet:.................... www.maico-ventilatoren.de
E-Mail:...................... technik@maico.de
8. Declaration of conformity
The DS-RC radio switch may be sold and operated in EU countries as well as in
CH, IS and N. Maico herewith declares that the DS-RC radio switch is in
compliance with the fundamental requirements and other relevant provisions of the
R & TTE Directive 1999/5/EC.
= top,
Command
ON, ventilation level up
Ventilation level down, OFF
PushPull ventilation. Ventilation with heat recovery
Cross ventilation. Ventilation without heat recovery
Speed up. Ventilation level 5 for 30 min. (Factory setting)
Sleeping function. OFF for 60 min. (Factory setting)
Auto-PushPull ventilation. With connected. Sensor only
Auto-Cross ventilation. With connected. Sensor only
= bottom)
2