Pipe For Gas Connection; Electrical Connection; Equipotential; Checking Heat Output - Lotus cooker PC1T-64G Instructions Pour L'installation Et L'emploi

Cuisinieres avec four usage professionnel

Masquer les pouces

Table des Matières

Les langues disponibles

Regulations 1985; The Building Standards Regulations, 1981, the IEE Regulations and the by-laws of the local Water

Undertaking.

The local gas Region or LPG supplier and the local authority and the relevant recommendation of the British Standards

(latest editions) concerned.

The installation, transformation and repair of appliances for professional kitchens as well as removal due to

malfunction,

and the supply of gas, may be made only by means of a maintenance contract stipulated with an authorised sales office

and in observance of technical regulations.

The appliance can be installed by itself or in a series side by side with appliances produced by us. There must be a

minimum distance of at least 10 cm between the appliance and the sides of the nearby cabinets made of inflammable

material. Take suitable measures to guarantee thermal insulation of the inflammable sides, such as, for example, the

installation of protection against radiation. The appliances must be installed in a suitable manner, observing the safety

standards. The small feet are adjustable to level the appliance.

The gas connection must be done with steel or copper pipes, or otherwise with flexible steel pipes in compliance with

the national norms, if any exist. Each appliance must be provided with a cut-off cock for rapid interruption of the gas

supply. Once the appliance has been installed, it is necessary to check for gas leaks for the pipe fittings; do not use a

flame for this purpose but a non-corrosive substance such as soapy water or foamy substances as contained in leak-

finder sprays. All our appliances undergo careful testing: the type of gas, the operating pressure and the category are

indicated on the data plate.

NB: The year of the appliance manufacture is shown in item "N" on the data plate. The first two numbers (e.g. 93..)

represent the year of manufacture.

The appliance is delivered with its power supply cable. If it has to be changed for any reason, disconnect it from the

arrival terminal block that is at the bottom of the front panel in the case of cookers, and at the bottom of the back panel

in the case of hobs (see Fig. A).

Put the cable through the grommet and cable lock, connect the wires to their relative terminals on the terminal block and

secure them. The earth wire must be longer than the others so that if the cable lock breaks it comes away after the power

wires.

Please Note: The power supply cable must have the following characteristics: it must be a silicone type (to

withstand a temperature of 180°C), and its section must be suitable for the appliance's power (see the

technical data table).

The appliance must be connected to an equipotential system.

The connection screw is positioned at the back of the appliance and is identified by the

Attention! The manufacturer will neither be held responsible for, nor will give any compensation during the guarantee

period for any damage caused, and which is due to inadequate installations not compliant with the instructions.

The appliances must be checked in such a way as to verify that the heat output is correct:

•

The heat output (thermal power) is indicated on the data plate of the appliance.

•

Firstly, check that the appliance can be used with the type of gas supplied; then check that the indication on the

plate corresponds to the gas to be used. For converting to another type of gas, check that the type of gas complies

with what is stated in this instruction manual.

The pressure is read with a gauge (minimum resolution of 0.1 mbar) inserted in the relative pressure outlet..

Remove the hermetically closed screw and insert the gauge pipe.

After reading, put back the screw tightening it hermetically and check for pressure leaks.

Connection for liquid gas G30/G31

The connection pressure for liquid gas is 30 mbar with butane and 37 mbar with propane.

Check the plate, read the pressure and verify that the description of the nozzle installed corresponds to the one supplied

by the manufacturer.

Connection with natural gas H G20

The connection pressure for natural gas is 20 mbar.

Check the plate, read the pressure and verify that the description of the nozzle installed corresponds to the one supplied

by the manufacturer.