Eudora GSI 6104 Mode D'emploi page 6

Options
NOTE: All the options must be set after selecting one of the programmes.
5
• Delayed start (Delay)
and the display shows the delayed start symbol (
the delay time by 1 hour, up to a maximum of 12 hours. The next press of the button deactivates the function; the "clock" symbol disappears and the duration
of the selected programme reappears in the numerical area. Once the delay time has been set, close the dishwasher door and press the start button (if
necessary); the delay time countdown will begin and the clock symbol will begin to flash until the selected programme begins. Until the programme begins, the
Display will show the remaining time when the door is opened.
To deactivate the delay, RESET the machine.
• Quick wash (IF APPLICABLE):
The "QUICK WASH ( ) symbol appears on the display when the button is pressed. At this point the machine is ready to start the wash programme.
• Half load (IF APPLICABLE):
The "1/2 LOAD" option is deactivated by default and the machine therefore washes loads on both upper and lower racks. If the "1/2 LOAD" button is pressed
once the wash will be performed using the upper rack only (this will be indicated by the corresponding
symbol on the display, ( )If the button is pressed again the wash will be performed on the lower rack only and the lower rack symbol (
If the button is pressed once more the "1/2 LOAD" function will be deactivated. The "1/2 LOAD" function may be activated with all programmes and is
deactivated at the end of the programme.
NOTE: When the half load function is activated the duration of the wash cycle is reduced.
• 3 in 1 FUNCTION: Press and hold button
is emitted and the tablet symbol (
5 seconds, when the tablet symbol disappears from the display.
The use of combined detergents (such as 3 in 1 tablets or similar products) may remove the need for rinse aid and salt. The "3 in 1" function may be activated for
all programmes; the rinse aid indicator light is deactivated.
N.B. It is good practice to follow the instructions given on the container for the products mentioned above.
- Up to a water hardness of 21° dH (37° f) it is not necessary to use salt; set the regeneration adjustment to D1 (see paragraph entitled "adjusting the water
softening system").
- Where water hardness is greater than 21° dH (37° f), salt must be used.
In this case fill the salt compartment and adjust the regeneration system to position D3.
Advice: Superior washing results can be achieved with the use of traditional detergents combined with salt and rinse aid.
WARNING: When traditional detergents are used the water softening system must be adjusted accordingly.
TABLE OF WASH PROGRAMMES (display version)
Rinse P1
Rapid 40º C
P2
P3
ECO 45º C
Normal 55º C
P4
(EN 50242)
P5
Intensive 65º C
(Optional)
Rapid 30º C
TABLE OF ERROR CODES
N.B.: Anomalies are signalled in the following way:
A continuous beep sounds until the programme with the error is reset.
Error
When this occurs
LED 4
At the beginning
of the cycle
N.B.: Upon contacting the authorised technical assistance centre always communicate the type of error
encountered.
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
6
1 2 3 4 5 6 7 8 9 0
GB
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
This button is used to set a delay time between 1 and 12 hours. The first time the button is pressed the function is activated
), while the text "1H" is displayed in the numerical area. Each subsequent press of the button increases
5
QUICK WASH (or 1/2 LOAD if provided) for 5 seconds; the "3 in 1" function is activated, a confirmation beep
). is shown on the display. This function remains active for all programmes, until it is deactivated by pressing button
BUTTONS DETERGENT
Pans and dishes until
the next wash cycle
Little dirty dishes
Very dirty delicate dishes
Normally dirty dishes
Very dirty dishes (except
delicate pieces)
Little dirty dishes
Checks to carry out
- Tap closed
- Filter of loading tube blocked
- Water supply tube bent
- Insufficient water pressure
Dishes
and
degree of dirt
Short cold wash to prevent food residue from
drying up and forming crusts on the dishes
Main wash
2 rinses (1 cold – 1 warm)
1 cold pre-wash - Main wash
2 rinses (1 cold – 1 warm)
1 cold pre-wash – Main wash
2 rinses (2 cold – 1 warm)
1 warm Pre-wash – Main wash
3 rinses (2 cold – 1 warm)
Main wash
2 rinses warm
- Reset the dishwasher
- Check
- Reset the dishwasher
- Verify the water pressure
)will be shown.
Cycle
description
Action to be taken
5
for