Programme Selection; Stopping The Machine - Eudora GSI 6104 Mode D'emploi

Description of control buttons and indication lights
1) ON/OFF On/off button Press this button to switch the appliance on
2) Low salt indicator light (if fitted)
3) Low rinse aid indicator light (if fitted)
4) "Delay" delayed start selector
5) Quick wash / half load selector (if fitted)
6) Programme selector button
7) Programme Start - Stop/pause button
8) Multifunctional display
9) Door handle
To open the door, pull forwards (an electrical safety device will switch the machine off when the door is opened).
18
1
Start-up
After checking the quantity of salt (only in models with salt compartment) and rinse aid, open
the water inlet valve completely, place the crockery in the racks, pour the main wash detergent and pre-wash detergent (if
necessary) into the compartment and close the door at the front of the machine.
Proceed as follows:
• Activate the "on-off" button

Programme selection

• Select the desired programme using button
programme will be shown, and the corresponding duration will appear on the Display. Select the programme most suited to
the type of crockery to be washed.
At this point the machine is ready to start the wash programme.
Start / Pause
• Close the door and press button
corresponding to the selected programme (e.g.
be shown, relating to the washing phase the machine is currently performing.
Pressing button again pauses the machine; the graphics disappear from the Display but the time remaining until the end
7
of the wash cycle and the start symbol begin to flash.
Incorrect programme settings (changing the programme or using RESET)
• To modify a programme which is already in progress, press button
segment will appear on the Display, indicating the reset stage is in progress.
N.B. The buzzer sounds to confirm the end of the RESET, while the text "End" is shown on the display. At this point
the machine is ready to be set again.
• If you have forgotten to place something inside the machine, the wash cycle may be paused (preferably only if the programme
started a short time before): press the pause button
close the door and press the Start button
• To repeat the wash, confirm the displayed programme by pressing the programme selector button
button 7 .
NOTE: if the power supply is suddenly cut off, the wash programme will restart from the point at which it was
interrupted.

Stopping the machine

At the end of the cycle the dishwasher stops automatically and 3 beeps sound three times to confirm the end of the wash
cycle. The text "End" appears on the Display.
To switch off the appliance press the on/off button
dishwasher from the water supply network.
ADVICE: After the beeps signalling the end of the cycle, to accelerate the drying phase the door may be left ajar.
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
4
1 2 3 4 5 6 7 8 9 0
GB
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
9
; the display will light up
1
6
(programme selector); each time the button is pressed the following
7
; the machine will begin the wash cycle. The start symbol
)will be shown on the display. A cycle of graphical information (A) will then
7
, open the door and place the crockery inside. To restart the machine,
again; the cycle will start from the point at which it was interrupted.
7
1
. After each wash cycle, close the water inlet completely to cut off the
2 3
8
4 5 6 7
and show the most recent programme performed
8
Start/Pause for approximately 6 seconds; a scrolling
7
-Pre-wash
-Wash
-Rinses
-Dry
and the symbol
followed by the start
6