Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2
Installation
Refer to the nearest Authorised Service Agent for
installation of your product.
C
Preparation of location and electrical installation for
the product is under customer's responsibility.
B
Installation and electrical connections must be
carried out by a qualified personnel.
A
Prior to installation, visually check if the product
has any defects on it. If so, do not have it installed.
Damaged products will cause risks for your safety.
Appropriate installation location
• Install the product in an environment which has no
risk of freezing and is in a stable and level position.
• Operate your product in a well ventilated, dust-free
environment.
• Do not block the air ducts in front of and under the
product with materials such as long pile rugs and
wooden bands.
• Do not place your product on a long pile rug or on
similar surfaces.
• Do not install the product behind a door with a lock,
sliding door or a hinged door which can strike the
product.
• Once the product is installed, it should stay at the
same place where its connections have been made.
When installing the product, make sure that the rear
wall of it does not touch anywhere (tap, socket, etc.)
and also pay attention to install the product at a
place where it will stay permanently.
B
Do not place the product on top of the power cable.
• Keep at least 1.5 cm distance to walls of other
furniture.
Under counter installation
• A special part (Part no: 295 970 0100) replacing
the top trim must be provided and installed by the
Authorised Service Agent in order to use the machine
under a counter or in a cupboard. It should never be
operated without the top trim.
• Leave at least 3 cm of space between the side
and rear walls of the product and the walls of the
counter/cupboard when installing your product under
a counter or in a cupboard.
Mounting over a washing machine
• A fitting device should be used between the two
machines when installing above a washing machine.
The bracket (Part no. 296 280 0100 white/296
280 0200 grey) must be installed by the Authorised
Service Agent.
• Place the product on a firm floor. If it will be placed
on top of a washing machine, the approximate
weight of both machines may reach 180 kg when
they are full. Therefore, the floor must be capable of
carrying the load on it!
Ventilation hose and connection (for
products equipped with an outlet vent)
Ventilation hose allows exhaust air from inside the
machine
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes can be
used instead of a hose. The pipe diameter should be
minimum 10 cm.
Maximum hose and pipe lengths are given in the table
below.
Maximum length
1 elbow 45°
1 elbow 90°
1 elbow 90° short
1 wall passage
C
Each elbow and other passages should be subtracted
from the maximum length stated above.
To connect a ventilation hose;
1. Connect the air outlet hose to the hose spacer piece
by turning it counterclockwise.
2. Make the hose passages as shown below.
C
Exhaust of humid air from the dryer into the room is
inconvenient. It may damage the walls and furniture
in the room.
C
The ventilation hose can be routed outdoors via a
window or it can be connected to the air outlet in the
bathroom.
C
Air outlet hose must be routed directly to the
outdoors. There must be a limited number of elbows
as not to hinder ventilation.
C
To prevent water accumulation in the hose, make
sure that it is not folded on the floor.
B
The ventilation hose should not be connected to the
chimney of a stove or a fireplace.
B
Do not operate your product at the same time with
heaters such as a coal or gas stove. Airflow may
cause the chimney to flare up.
5 EN
Hose
Pipe
4 m
5 m
-1.0 m
-0.3 m
-1.8 m
-0.6 m
-2.7 m
-2.0 m
-2.0 m
Publicité
Table des Matières
