Virutex FR277R Mode D'emploi page 8

Vibration total values..............................................a
Uncertainty....................................................................K: 1.5 m/s
2. OPERATION RANGE
The router is a professional power tool intended for
surface milling of wood, plastics and aluminium. It is an
excellent tool for milling templates, contours, circles and
grooves, for making finishing laths and picture frames
and for engraving inscriptions.
3. SAFETY INSTRUCTIONS FOR
MACHINE OPERATION
Read the instructions for use and safety instructions
carefully before using the tool.
• Disconnect the plug before you perform any work
on the tool.
• Do not use the tool if the mains lead is damged. If the
mains lead is damaged while working, do not touch it
but immediately disconnect the plug.
• Always keep the mains lead away from moving parts
of the tool.
Direct the mais lead to the rear fo the tool.
• Use only extension cord that is intended for outdoor
use and equipped with a splash-proof coupling-socket.
Connect the tool via a fault current (FI) circuit beaker
with a triggering current of 30 mA maximum.
• Wires of the extension cable must have a minimum
section of 1,5 mm2 and the cable must be fully unwound.
• Plug in the tool only if the switch is turned off.
• Always wear personal protective equipment, glasses
and footwear.
• Always hold the router with both hands.
• Switch off the motor after you have finished milling.
• Before you put down the tool, loosen the router table.
• Always put down the tool on a horizontal and clean
surface.
• Do not put any other tools on the workpiece.
• Workpiece must be clean, without any rests of ma-
terials, sawdust...
• Work place should have adequte lights, it is forbiidden
to use the tool in rooms with inflammable substances
and gases, switch on/off the tool only by the switch and
not by disconnesting the plug.
• Be careful of screws, nails and other objects in the
workpiece while milling.
• Start working only when the tool has reached full speed.
• Be aware of the sudden impact when the FR277R and
FR278R power tool is switched on.
• Prevent unintentional switching on of the tool.
• Always use undamaged and sharp router bits.
• When you do not use the tool, store it in a dry place
protected from dust.
• Do not wear loose clothes of jewelry the tool could
take hold of and pull it towards it. If you have long hair,
8
: 4.4 m/s wear a protective head-covering. When working outside,
2
h
wear non-skid footwear.
2
• In case the tool is blocked, immediately switch off the
tool and disconnect the plug.
• Clamp the workpiece.
• Guide only switched on tool towards the workpice.
Switch off the tool when you when you have lifted the
tool from the workpiece.
• Use only original parts and accessories.
4. PACKAGE CONTENTS
Router
Parallel guide
Compass
Wrench
Dust extraction adapter
Instructions for use, guarantee card
5. PREPARING THE TOOL FOR MILLING
6. DUST SUCTION
Milling and grinding wood generate sawdust and dust
that endanger safety and health. Using dust suction
prevents air pollution for breathing and makes easier
removal of wastes.
7. MOUNTING DUST EXTRACTION ADAPTER
Put the dust extraction adapter 15 (Fig. 2) baseplate 3
(Fig. 2) so that the twin column guide A (Fig. 2) is inside
the mouth of the dust extraction adapter.
Push the mouth with the right hand thumb in the
direction A (Fig. 2) towards the locking edge C so that
the lock D on the periphery is automatically cought in
the edge B (Fig. 2)
Connect the hose of a vacuum cleaner directly to the
dust extraction adapter 15 (Fig. 3), or connect it with a
suction hose with a turning connection for extracting
dust 4 (Fig. 3).
Fix the latter into the corresponding place below the
motor cover.
Mount the upper dust extraction adapter by pushing
it in the directions C until it snaps between the motor
gerabox and the motor cover. Then attach the lower
part of the hose to the dust extraction adapter 15 in
the direction D (Fig. 3).
Turning connection enables better view of the milling
area and setting the vacuum cleaner hose in the most
favourable position. The diameter of the dust extrac-
Always disconnect the plug from power
source before making any adjustments
or changing any accessory.