Declaration Of Conformity - Skil 8600 Notice Originale

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
uSe
• On/off
- switch on the tool by pulling trigger A
- lock the switch for continuous use by pressing button B
- unlock the switch by pulling again trigger A and then
releasing it
- switch off the tool by releasing trigger A
! before switching on the tool, ensure that it is not
in contact with any object
! after switching off the tool the motor continues to
run for a few seconds
• Blowing 6
- insert tabs inside nozzle C into slots of air outlet D
and lock nozzle into place by turning it clockwise
! when blowing always ensure that air inlet E 2 is
kept clear of debris/impurities
• Vacuuming 7
- insert tabs inside nozzle C into slots of air inlet E and
lock nozzle into place by turning it clockwise
- do not vacuum sharp-edged or hot materials (such
as glass splinters, hot ash or metal chips)
! when vacuuming always mount dustbag F onto
air outlet D
- regularly empty dustbag F (the vacuum capacity
decreases considerably when the dustbag is full)
• Airflow control (7 positions)
- turn wheel G upwards for increasing the air volume
- turn wheel G downwards for reducing the air volume
APPLICATION ADVICE
maINTeNaNce / ServIce
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots H 2)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
• A damaged power cord shall be replaced at a SKIL
service centre only in order to avoid a hazard
eNvIroNmeNT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60335, EN 61000,
EN 55014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
19.07.2010
NoISe/vIbraTIoN
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 85 dB(A) and the sound
power level 96 dB(A) (standard deviation: 3 dB),
and the vibration 5.0 m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
significantly reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing
your work patterns
F
Souffleur/aspirateur
INTroDucTIoN
• Cet outil a été conçu pour souffler et aspirer les
matériaux qui ne sont pas dangereux à la santé
• Cet outil ne convient pas au soufflage et à l'aspiration
de matériaux inflammables, de copeaux métalliques et
d'objets tranchants (comme les vis ou les clous)
5
Jan Trommelen
Approval Manager
8600