Connections; Choosing A Connection - Samsung DVD-D360K Manuel D'utilisation

1. DVD POWER Button
Turns the power on or off.
2. DVD Button
(Only DVD-D530)
Use to select the DVD player for operation.
3. TV Button
(Only DVD-D530)
Use to select a Samsung TV for operation.
4. EZ VIEW Button
(Only DVD-D530)
Lets you easily adjust the aspect ratio of a
picture according to the screen size of your
TV (16:9 or 4:3).
5. MARKER Button
To make bookmark of the disc.
6. REPEAT Button
Allows you to repeat play a title, chapter,
track, or disc.
7. DISC MENU Button
Brings up the Disc menu.
8. RECORD Button
(Only DVD-D360K)
Use to Karaoke recording.
9. TV VOL (+, -) Buttons
(Only DVD-D530)
Controls volume.
10. SKIP Buttons ( / )
Use to skip the title, chapter or track.
11. STOP Button ( )
To stop the disc
12. MENU Button
Brings up the DVD player's menu.
13. ENTER/π/†,√/® Buttons
This button functions as a toggle switch.
14. TOOLS Button
Displays the current disc mode. It also lets
you access the Display function.
15. OPEN/CLOSE ( ) Button
To open and close the disc tray.
16. HDMI SEL. Button

Connections

Choosing a Connection

The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect
any cables.
- Refer to the user's manual of the additional components you are connecting for more informa
tion on those particular components.
4
(Only DVD-D530)
HDMI Output resolution setup.
17. USB Button
To change device which access to USB
device.
18. VIDEO SEL. Button
Changes video output mode.
19. REPEAT A-B Button
(Only DVD-D530)
Allows you to repeat play a chosen section
(A-B) on a disc.
20. INFO Button
Used to displays playback info banner.
21. TITLE MENU Button
Brings up the Title menu.
22. AUDIO/TV SOURCE Button
Use this button to access various audio
functions on a disc. Use this button to select
an available TV source (mode TV).
23. PAUSE Button ( )
(Only DVD-D530)
Pauses disc play.
24. SEARCH Buttons ( / )
Allows you to search forward/backward
through a disc.
25. TV CH ( , ) Buttons
(Only DVD-D530)
Channel selection.
26. PLAY Button ( )/( )
Begins disc play.
27. RETURN Button
Returns to a previous menu.
28. SUBTITLE/(π) Button
29. EXIT Button
(Only DVD-D530)
Exits the on-screen menu.
30. KARAOKE (†) Button
(Only DVD-D360K)
To acces karaoke menu (keycon, mic
volume,echo).
A. Connecting to a TV (SCART)
1. Using Scart cable, connect to SCART terminal on the rear of the DVD player to the SCART IN
terminals of TV.
2. Turn on the DVD player and TV.
3. Press the input selector on your TV remote control until the Video signal from the DVD player
appears on the TV screen.
B. Connecting to a TV (For Video)
1. Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals
on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of
TV.
2. Turn on the DVD player and TV.
3. Press the input selector on your TV remote control until the Video signal from the DVD player
appears on the TV screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page.
- The position of terminals can vary depending on your TV set. Please refer to the user's manual of the
TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of
the DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN ➝ SCART-RGB ➝ SCART-
CVBS).
C. Connection to a TV (Interlace/Progressive)
1. Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of
the DVD player to the COMPONENT IN terminal of TV.
2. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the
DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV.
3. Press the input selector on your TV remote control until the Component signal from the DVD
player appears on the TV screen.
4. Set the Video Output to I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO
SEL. button to change the Video Output mode.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
- There is no component video displayed when "SCART-RGB" Selected by pressing VIDEO SELECT
button on remote control.
D. Connecting to a TV with DVI/HDMI Jack (ONLY DVD-D530)
1. Using the HDMI-DVI/HDMI-HDMI cable , connect the HDMI OUT terminal on the rear of the
DVD player to the DVI/HDMI IN terminal of your TV.
2. Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the
DVD player to the AUDIO (red and white) IN terminals of your TV. Turn on the DVD player and TV.
3. Press the input selector on your TV remote control until the DVI/HDMI signal from the DVD
player appears on your TV screen.