Safety Information; Fueling The Heater - Stanley ST-70-SS-E Guide D'utilisation

Safety Information

This is a paraffin/diesel, direct-fired, radiant heater. It is primarily
intended for use for temporary heating of buildings under construc-
tion, alteration or repair. This appliance produces small amounts of
carbon monoxide. WARNING! Risk of indoor air pollution! Use
this heater only in well ventilated areas! Provide at least a 2,800
sq cm opening of outside air for every 29,3 kw/hr or 100,000 BTU/
hr of heater rating. Provide a larger opening if more heaters are
being used.
Carbon Monoxide poisoning may lead to
DANGER
death!
Risk of burns / fire / explosion! NEVER
WARNING
use fuel such as gasoline, benzene, alcohol,
white gas, camp stove fuel, paint thinners, or other oil compounds
in this heater (THESE ARE VOLATILE FUELS THAT CAN
CAUSE A FIRE OR EXPLOSION).
Fire, burn, inhalation, and explosion
WARNING
hazard. Keep combustibles a safe distance
away from the heater as recommended by these instructions.
Never use the heater in spaces which contain products such
as gasoline, solvents, paint thinners, dust particles, volatile or
airborne combustibles, or any unknown chemicals. This is an
unvented portable heater. It uses air (oxygen) from the area in
which it is used. Adequate combustion and ventilation air must
be provided.
Do not operate this heater until you have
WARNING
read, and thoroughly understand these
safety and operating instructions. Failure to comply with the
precautions and instructions provided with this heater can result
in death, serious bodily injury, property loss or damage from the
hazards of fire, soot production, explosion, burns, asphyxiation
or carbon monoxide poisoning. Only persons who can read and
understand these instructions should use or service this heater.
Retain this manual for your reference.
Minimum Distance From Combustibles
Top
ST-70T-SS-E 1.2 m
- NEVER refill the heater's fuel tank while heater is operating or
still hot. This heater is EXTREMELY HOT while in operation.
- Keep all combustible materials away from this heater.
- NEVER block air inlet (rear) or air outlet (front) of heater.
- NEVER use duct work in front or at rear of heater.
- NEVER move or handle heater while still hot.
- NEVER transport heater with fuel in its tank.
- If equipped with a thermostat, the heater may start at any time.
- ALWAYS locate heater on a stable and level surface.
- ALWAYS keep children and animals away from heater.
- Bulk fuel storage should be a minimum of 7.6m (25 ft). from
heaters, torches, portable generators, or other sources of
ignition.
- ALWAYS unplug the heater when not in use.
- Not for use in homes or recreational vehicles.
- Never use this heater in living or sleeping areas.
- NEVER use heater where flam mable vapors may be present.
- Use only the electrical power (voltage and frequency) specified
on the model plate of the heater.
- ALWAYS install the heater so that it is not directly exposed to
water spray, rain, dripping water, or wind.
- NEVER store fuel in direct sunlight, indoors, or near a source of
heat.
- NEVER use fuel that has been stored from one season to the
next. Fuel deteriorates over time. OLD FUEL WILL NOT BURN
PROPERLY IN THIS HEATER.
- NEVER operate this heater UNATTENDED!
© 2013, Pinnacle Products International, Inc.
Sides Front
1.2 m 2.4 m
10
Assembly
1. Attach handle by lining up holes of handle with the holes
in the upper shell of heater (See fig. 1).
2. Insert screws and tighten.
Figure 1
Ventilation
ALWAYS provide a fresh air opening in the heated space
of at least 2,800 sq.cm for each 29 Kw/Hr. of heater
output. Provide a larger opening if more heaters are being
used.

Fueling the Heater

Never fill the fuel tank indoors. Always fill the tank
outdoors. Be sure that the heater is on level ground
when fueling, and never overfill the fuel tank.
It is always a good idea to fire the heater outdoors for the
first time. This will allow any oils used in the manufacturing
process to be burned off in a safe environment. This initial
burn should last at least 10 minutes.
NOTE: On first ignition or after refueling, you may hear
a grinding sound just before ignition. This is the fuel
pump removing air from the fuel line. Your heater will
start up within seconds. If it does not start, repeat
Step #4 with fuel gauge reading at least 1/2 tank.
Operation
To Start the Heater
1. Fill tank with paraffin/diesel until fuel gauge points to "F".
2. Be sure fuel cap is secure.
3. Plug power supply cable into a suitable power socket.
4. A) ST-70T Only:Turn thermostat control knob to desired
temperature setting. The setting range is from ~~5° C to
45° C~~.
B) Push the Power switch to the "ON" position. The
power indicator lamp and room temperature display will
light and the heater will start
To Stop the Heater
Do not disconnect the power source or
WARNING
unplug the power cord until the cooling
cycle has been completed!
1. Turn the Temp. Setting Knob to left.
2. Turn the Operating switch to "OFF" position.
Combustion will stop, and the Cooling Cycle
(approx. 7 minutes / 70T-SS approx. 3-4 minutes) will
begin.
To Restart the Heater
1. Wait ten seconds after cooling cycle has completed.
2. Turn the Operating Switch to "ON" position.
3. Be sure to follow all starting procedure precautions.