JTS IN-64R Mode D'emploi page 11

Note: To exit the adjusting mode without making an
adjustment, press the button SET. The display will show
("cancel") and the unit will return to normal operation.
3) To activate the lock, press the button "up"
will be displayed.
4) Confirm the activation with the button SET.
("store") will be shortly displayed and the unit will go
to normal operation.
Deactivating the lock
1) Keep the button SET (6) pressed for approx. 2 sec-
onds until is displayed.
2) To deactivate the lock, press the button "down"
(5). will be displayed.
3) Confirm the adjustment with the button SET.
("store") will be shortly displayed and the unit will go
to normal operation.
6.2 Automatic frequency adjustment of the
transmitter (REMOSET function)
Via a radio signal of the receiver, the transmitter will be
set to the same transmission frequency. The maximum
range of the REMOSET transmission will be 10 m.
When the desired transmission frequency has been
adjusted on the receiver (
lock function has been deactivated (
and the transmitter has been switched on, press the
button REMOSET (3). When the REMOSET function
is activated, the illuminated ring of the button will flash
rapidly and the display will show the identification
number of the receiver (
ing out the frequency adjustment, the receiver and the
transmitter will be set to the same channel group and
the same channel; the illuminated ring of the button
will light permanently again.
If the illuminated ring keeps flashing continuously after
activating the REMOSET function, the receiver will not
get a radio signal from the transmitter on the transmis-
sion frequency adjusted, e. g. in case of failure of the
REMOSET transmission (elimination of error
below) or muting of the transmitter at the time of
REMOSET transmission.
If the transmitter has not adjusted itself to the channel
group and the channel of the receiver, check the following
adjustments on the transmitter:
→ Has the lock function been activated on the transmitter?
→ Has the REMOSET transmission been deactivated on
the transmitter?
→ Does the identification number adjusted on the trans-
mitter differ from the one adjusted on the receiver?
Correct the corresponding adjustment on the transmitter
and press the button REMOSET once again.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
chapter 6.1.1), when the
chapter 6.1.3)
chapter 6.1.2). After carry-
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
7 Specifications
Type of unit: . . . . . . . . . . . PLL multifrequency
L
(7).
Radio frequency range: . . 790 – 814 MHz, divided into
Audio frequency range: . . 40 – 18 000 Hz
REMOSET transmission: . 2.4 GHz
THD: . . . . . . . . . . . . . . . . < 0.6 %
Dynamic range: . . . . . . . . > 105 dB
Noise suppression: . . . . . pilot tone squelch,
M
Audio outputs
XLR, bal.: . . . . . . . . . . . 300 mV
6.3 mm jack, bal.: . . . . . 150 mV
Ambient temperature: . . . 0 – 40 °C
Power supply: . . . . . . . . . 12 – 18 V /600 mA via
Dimensions (W × H × D): 210 × 42 × 175 mm
Weight: . . . . . . . . . . . . . . . 445 g
7.1 Transmission frequencies (in MHz)
Group
Channel
1 790.875
2 792.625
3 794.250
4 795.625
5 797.125
6 798.875
box
7 801.125
8 802.250
9 803.625
10 805.250
11 805.750
12 808.625
13 809.125
14 810.000
15 813.250
16 813.750
Subject to technical modification.
®
receiver with diversity
technique
64 channels (
noise mute
the power supply unit
provided connected to
230 V~/50 Hz
(antennas folded down)
A B C
790.750 791.125
791.375 791.750
793.125 792.625
794.000 793.750
795.250 794.500
796.250 796.125
796.875 796.875
798.000 798.250
798.875 799.000
800.250 800.875
803.250 804.500
804.000 805.875
805.625 806.625
806.750 807.750
808.250 808.375
813.750 813.750
table)
D
790.625
791.125
791.875
793.625
795.875
797.125
797.875
799.125
800.875
801.375
802.875
803.375
804.125
806.250
807.625
813.625
11