Information On Safeties; General Precautions; Mechanical Safeties; Electrical Safeties - Diamond GPR 220 Installation

Table des Matières

Publicité

1.1 GENERAL PRECAUTIONS

• THE SLICER MUST BE MANAGED BY SKILLED PERSONNEL, FAMILIAR WITH THE INSTRUCTIONS
FOR USE AND SAFETY CONTAINED IN THIS MANUAL.
• IN THE CASE OF ROTATION OF THE PERSONNEL, VOCATIONAL TRAINING IS NECESSARY.
• EVEN IF THE MACHINE COMES WITH SEVERAL SAFETY SYSTEMS, AVOID SETTING THE HANDS
NEAR THE BLADE AND MOVING PARTS.
• BEFORE THE CLEANING AND MAINTENANCE OPERATIONS, CHECK TO MAKE SURE THE
MACHINE IS DISCONNECTED FROM THE MAINS.
• PERIODICALY CHECK CABLE AND ELECTRIC ELEMENTS CONDITIONS.
• NEVER USE THE SLICER FOR CUTTING FREEZED FOOD, MEAT AND FISH WITH BONES, OR FOR
NON-FOOD PRODUCTS.
• WHENEVER THE BLADE DIAMETER IS REDUCED OF MORE THAN 10 MMS., APPLY TO THE
ASSISTANCE SERVICE FOR REPLACEMENT.
• NEVER CARRY OUT REPEARING OPERATIONS PERSONNALLY, BUT APPLY ALWAYS TO
SKILLED PERSONNEL.

1.2 MECHANICAL SAFETIES

THE SLICERS WE PRODUCE AND WHICH ARE DESCRIBED IN THIS MANUAL MEET, AS FAR AS
SAFETIES ARE CONCERNED, THE PRESCRIPTIONS ON THE RISKS OF MECHANICAL TYPE
ISSUED BY E.E.C. AS : 89/392 - 91/368 - 93/44 - 93/68. FOR THE SANITARY REGULATIONS THEY
COMPLY WITH THE RULE E.E.C. 89/109.

1.3 ELECTRICAL SAFETIES

THE
SAFETIES AGAINST ELECTRICAL RISKS COMPLY
REGULATIONS CENELEC EN 335/2 /64
ALL OUR SLICERS TYPE GPR INCLUDE A LOW VOLTAGE ELECTRIC CIRCUIT AND TWO BUTTONS
FOR STARTING AND STOPPING THE MACHINE.
ON THE LOW VOLTAGE CONTROL CIRCUIT IS SET A RELAY FOR RESTARTING THE MACHINE
WHENEVER A FORTUITOUS LACK OF CURRENT OCCURS.
ALL OUR SLICERS TYPE FAP INCLUDE A RELAY FOR RESTARTING THE MACHINE WHENEVER A
FORTUITOUS LACK OF CURRENT OCCURS.
DUE TO THE PERFECT INSULATION OF ALL THE ELECTRIC ELEMENTS AND THE REMARKABLE
RESISTANCE OF ALL THE MATERIALS USED, OUR MACHINES CAN BE INSTALLED TO WORK INSIDE
MOIST PREMISES.
ATTENTION: DO NOT USE WATER TO CLEAN THE SLICER, ONLY A HUMID CLOTH
WARNING:
IN CONFORMITY WITH POINT 1.7.2.
CONTAINED IN THE E.E.C. REGULATIONS 80/392 AND 91/368, THESE PROTECTIONS AND SAFETIES
STRICTLY COMPLY WITH THESE REGULATIONS.
WE POINT OUT HOWEVER THAT THE ABOVE MENTIONED PROTECTIONS, EVEN IF THEY SENSIBLY
REDUCE BOTH THE POSSIBILITY AND EXTENT OF THE DAMAGE, DO NOT ELIMINATE FULLY THE
RISK OF CUTTING.
TECHNICAL FEATURES OF THE SERIES OF SLICERS "GPR-FAP":
• POSSIBILITY OF INTERMITTENT WORK
• THEIR USE, CLEANING AND MAINTENANCE IS QUITE SAFE
• THANKS TO THEIR DESIGN AND TO THE REALIZATION OF ALL PARTS IN
• STAINLESS STEEL AND ANODIZED ALUMINIUM ALLOY WITHOUT EDGES
• FOR EASY CLEANING OPERATIONS, THESE SLICERS FULLY COMPLY WITH THE STRICTEST
SANITARY REGULATIONS.

1) INFORMATION ON SAFETIES

2) TECHNICAL FEATURES
WITH
THE RULE E.E.C 73/23 AND
"INSTRUCTIONS ON FURTHER RISKS"
10

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Gpr 250Gpr 300 sgFap 220Fap 250Fap 300Gpr 300 sg mn ... Afficher tout

Table des Matières