Fuse Replacement; Technical Data - Renkforce T-900B Mode D'emploi

• If you wish to connect a playback device to the monitor temporily only, connect its AV output to
the adapter cable enclosed (yellow = video, red = audio).
• Plug the phone jack of the adapter cable into the AV IN input (2) on the front of the monitor.
The connector VIDEO 1 IN will be deactivated as long as the adapter cable is plugged in.
• If you wish to use a headset, plug its connecting cable into the PHONE (1) connector on the front
of the monitor.
The inbuilt loudspeaker of the monitor will be deactivated as long as the headset is
plugged in.
Operation
(1) PHONE for the connection of a headset
(2) AV IN for the connection of external AV devices
(3) MODE toggles the display format (4:3/16:9)
(4) V1/V2 switches the video input (VIDEO 1 IN/VIDEO 2 IN)
(5) "-" turns the volume down or changes settings in the menu
(6) M is used to access the menu – the menu points are accessed by pressing several times,
settings are performed via the "-" and "+" keys
BRIGHTNESS brightness adjustment
CONTRAST contrast adjustment
SATURATION saturation adjustment
VOLUME volume adjustment
SOURCE selection of the input: VIDEO 1 IN/VIDEO 2 IN
RESET restore of factory settings
L/R mirroring of the display
rotation of the display
U/D
16:9/4:3 switching of the display format
EXIT exiting the menu
(7) "+" turns the volume up or changes the settings in the menu
(8) POWER switches the monitor on/off
(9) Infrared receiver for the remote control
(10) Power indicator - lights up when the device is turned on
(1) MUTE – switches the sound on/off
(2) MD toggles the display format (4:3/16:9)
(3) L/R mirrors the display (e.g. for use of a reversing camera)
(4) U/D rotates the display by 180° (if the monitor has been hung up)
(5) AV switches the video input (VIDEO 1 IN/VIDEO 2 IN)
(6) ON/OFF switches the monitor on/off
(7) Adjustment of the display brightness
(8) Adjustment of the display contrast
(9) Adjustment of the saturation of the display
(10) Adjustment of the volume
Fuse replacement
If it becomes necessary to replace a fuse, make sure that only fuses of the prescribed type and
nominal current are used (see "Technical Data").
You must not carry out your own repairs to fuses or bridge the fuse holder.
• Disconnect the monitor from the power supply.
• Unscrew the fuse holder in the red connection.
• Remove the defective fuse and replace it with a fuse of the same type.
• Close the fuse holder again.
• Only then the monitor should be re-connected to the car system and put into operation.
• Should the fuse trigger again, have the device repaired in a specialist workshop.
Disposal
a) Product
Electronic devices are recyclable waste materials and must not be disposed of in the
household waste!
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Remove the battery in the remote control and dispose of it separately from the product.
b) Batteries and Rechargeable Batteries
The end user is legally obliged (Battery Regulation) to return used batteries and rechargeable bat-
teries. Do not dispose of used batteries in the household waste!
Contaminated batteries/rechargeable batteries are labelled with these symbols to in-
dicate that disposal in the domestic waste is forbidden. The symbols for the relevant
heavy metals are: Cd=Cadmium, Hg=Mercury, Pb=Lead (marking can be seen on the
battery/rechargeable battery, e.g., underneath the rubbish bin symbol shown on the
left).
You can return used batteries/rechargeable batteries free of charge to any collect-
ing point in your local community, in our stores or in any other store where batteries/
rechargeable batteries are sold.
You thereby fulfil your statutory obligations and contribute to the protection of the environment.
Technical Data
Operating voltage................................................. 12 V/DC
Power consumption............................................. 500 mA
Battery for remote control .................................. 3 V lithium button cell CR2025
Fuse ........................................................................ T2AL/250V (5 x 20 mm)
Display size ........................................................... 22.9 cm (9")
Display format....................................................... 16:9
Definition ............................................................... 800 x 480
TV format ............................................................... PAL/NTSC
Dimensions (without mounting frame) ............. 226 x 157 x 30 mm
Installation opening ............................................. 163 x 232 mm
Mounting depth .................................................... 24 mm
Range of operating temperature ....................... 0 – 50 °C
Weight .................................................................... 490 g
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.