Black & Decker LAWN HOG MM675 Guide D'utilisation page 4

Masquer les pouces Voir aussi pour LAWN HOG MM675:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

ASSEMBLY INSTRUCTIONS
BEFORE ASSEMBLING YOUR MOWER, CHECK THAT YOU HAVE
RECEIVED THE FOLLOWING IN THE SHIPPING CARTON.
SEE FIGURE 1.
A. Mower
D. Discharge Chute
B. Upper Handle
E. Plastic Bag with 2 handle bolt and
C. Lower Handle
2 cable ties
A
1
E
ASSEMBLING THE HANDLE
1. Your mower carton contains the mower, 2 handles, discharge chute
and 1 plastic parts bag.
2. Fasten the upper and lower handle halves together using the eye
bolts (already installed on the power and flip cords) and the
handle knobs from the plastic bag. Make sure the power cord
and switch are on the same side of the mower as the
discharge area and that the flip locking mechanism is on the
opposite side. There are three holes on the upper handle, this
allows the handle height to be set in three positions. Choose the
hole that best suits your overall height. Install the eye bolts to the
outside of the handles so that the knobs are on the inside. Tighten
the knobs securely.
2A
ATTACHING THE HANDLE (FIGURE 2B)
1. UNPLUG TOOL, AND WAIT FOR BLADE TO COME TO A
COMPLETE STOP.
2. Brace the front end of the mower so that it cannot roll forward.
3. Align the ends of the lower handle vertically over the flip bracket
installation slots with the power cord on the same side as the
discharge area. (Figure 2B)
4. Spread the handle sightly and push the handle down until they
engage on the flip brackets, taking care not to pinch or damage
the power or flip cord.
5. Pull up on the handles to ensure a secure fit.
6. Install cable ties, from plastic bag, in locations shown on lower
handle.
2B
C
D
B
(FIGURE 2A)
REMOVING THE HANDLE (FIGURE 3)
1. UNPLUG TOOL, AND WAIT FOR BLADE TO COME TO A
COMPLETE STOP.
2. Brace the front rear of the mower so that it cannot roll backward.
3. Pull the handle release lever and rotate the handle to a vertical
position.
4. Grasp the ends of the lower handle with both hands. Pull the two
sides of the handle apart while pulling up on the handle. Be careful
not to damage cords when removing handle
WARNING: NEVER use a sharp object to move jacketed wires out
of the way.
3
2
1
MULCHING
The mower is designed to mulch or discharge the grass depending
on whether mulch door is closed (mulching) or the mulch door is up
and the discharge chute is in place (discharging). No further
assembly steps are required if you are mulching. PROCEED TO
OPERATING INSTRUCTIONS.
DISCHARGE CHUTE INSTALLATION (FIGURE 4)
(If you wish to discharge the clippings rather than mulch,
perform these steps)
1. UNPLUG TOOL, AND WAIT FOR BLADE TO COME TO A
COMPLETE STOP.
2. Open mulch door by pulling on the mulch door finger grip. (Figure 4A)
3. Align the discharge chute arrows with the positioning arrows on the
mower deck and insert the discharge chute as shown.
4. Position the chute until the chute hooks are trapped under the deck
hooks and release the chute and door. (Figure 4B)
4
A
OPERATING INSTRUCTIONS
NOTE: A mower is a major appliance and should not be
operated simultaneously with other major appliances on the same
house circuit.
WARNING: Make sure that other persons and pets are at least 100
feet away.
INSPECT CUTTING AREA
4
B
Remove all rocks, sticks, wire, toys, bones,
and other debris or items which might be
thrown by the rotating blades.

Publicité

Table des Matières
loading

Table des Matières