Maintenance Instructions; Lubrication; Cables; Clutch Jaw Assembly - RIDGID K-60SP Mode D'emploi

Tools for C-10 Cable
Catalog Model
No. No. Description
62850 T-101 Straight Auger
62855 T-102 Funnel Auger
27642 T-125 Retrieving Auger
62860 T-103 Sawtooth Cutter, 2
62865 T-104 "H" Cutter, 2
62870 T-105 Grease Cutter, 2
62875 T-106 Grease Cutter, 3
62880 T-107 Spade Cutter, 1
62915 T-109 Spiral Sawtooth Cutter, 1
62920 T-110 Spiral Sawtooth Cutter, 2
62925 T-111 Spiral Sawtooth Cutter, 3"
62930 T-112 4-Blade Cutter, 1
62935 T-113 4-Blade Cutter, 3"
98050 T-150 Sharktooth Cutter, 3" and 4"
98055 T-150-1 Sharktooth Cutter, 3" Blade
98060 T-150-2 Sharktooth Cutter, 4" Blade
62940 T-114 Chain Knocker
Tools for C-7, C-8, and C-9 Cables
Catalog Model
No. No. Description
62990 T-201 Straight Auger
62995 T-202 Bulb Auger, 1
63000 T-203 Bulb Auger,
55457 T-225 Retrieving Auger
63065 T-217 Drop Head
54837 T-204 "C" Cutter, 1"
63005 T-205 "C" Cutter, 1
63010 T-206 Funnel Auger
63015 T-207 Spiral Cutter, 1
63020 T-208 Spiral Cutter, 1
63025 T-209 Spiral Cutter, 2"
63030 T-210 Spade Cutter, 1"
63035 T-211 Spade Cutter, 1
63040 T-212 Spade Cutter, 1
63045 T-213 4-Blade Cutter, 1"
63050 T-214 4-Blade Cutter, 1
63055 T-215 4-Blade Cutter, 1
63060 T-216 Chain Knocker, 2"
63280 T-218 Flue Brush, 3"
63070 T-219 Flue Brush, 2
63080 T-220 Flue Brush, 2"
63220 T-221 Flue Brush, 1
52812 T-230 H-D "C" Cutter, 2"
52817 T-231 H-D "C" Cutter, 2
52822 T-232 H-D "C" Cutter, 3"
48482 T-250 Tool Set includes:
– T-203 – T-217
– T-205 – A-13
– T-210
999-997-050.10_REV. A
1 / "
2
1 / "
2
1 / "
2
1 / "
2
3 / "
4
3 / "
4
1 / "
4
3 / "
4
1 / " O.D.
8
7 / ", O.D.
8
3 / "
8
1 / "
4
1 / "
2
3 / "
8
3 / "
4
3 / "
8
3 / "
4
1 / "
2
1 / "
2
1 / "
2
K-60SP Drain Cleaning Machine
Miscellaneous
Catalog Model
No. No. Description
59360 A-3 Tool Box
59205 A-1 Left-Hand Mitt
59295 A-2 Right-Hand Mitt
59225 A-12 Pin Key,
59230 A-13 Pin Key,
61615 A-60-12 12' Rear Guide Hose for
59235 A-14-6 6' Rear Guide Hose for
C-9
84325 A-14-10 10' Rear Guide Hose for
C-8, C-9
59470 A-8 Cable Carrier (Holds 75'
59210 A-10 Cable Carrier (Holds 45'
Cable Carrier (Holds 90'
59425 A-36 Cable Caddy
65687 K-60SP Jaw Set
NOTE! See Ridge Tool Catalog for complete list of tools
and accessories.

Maintenance Instructions

WARNING
Make sure machine is unplugged from power source
before performing maintenance or making any ad-
justment.

Lubrication

Lubricate machine with grease at grease fitting (located on
jaw housing) once a week if used every day; once a
month if used less.
NOTE! No lubrication of the Motor Shaft is required.

Cables

Cables should be thoroughly flushed with water to prevent
damaging effects of drain cleaning compounds. Peri odi -
cally lubricate cables and couplings with RIDGID Cable
Rust Inhibitor.
When not in use, store cables indoors to prevent deterio-
ration by the elements.
Cables should be replaced when they become severely
corroded or worn. A worn cable can be identified when out-
side of coils become flat.
Clutch Jaw Assembly (Jaw Set)
The clutch jaw assembly should be periodically cleaned.
1. Stand the machine up on the front of the frame.
Make sure clutch handle is in its uppermost position.
Remove the two (2) socket head cap screws from the
jaw housing with a 1 / " hex key (Figure 11).
4
7 / " Cable
8
5 / " Cable
8
7 / " Cable/C-10
8
5 / " Cable/C-7, C-8,
8
5 / " Cable/C-7,
8
7 / " Cable/C-10)
8
7 / " Cable/C-10)
8
5 / " Cable/C-8, C-9)
8
11