Important Safety Instructions - Bosch NIT5066UC Instructions D'installation

IMPORTANT SAFETY INSTRUCTIONS

9
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT: THE APPLIANCE HAS TO BE INSTALLED
F E S A T A N R T P O A D I M R E
BY A QUALIFIED INSTALLER.
INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE
APPLIANCE AFTER INSTALLATION IS COMPLETE.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE
LOCAL ELECTRICAL INSPECTOR'S USE.
WARNING
If the information in this manual is not followed exactly,
fire or shock may result causing property damage or
personal injury.
WARNING
Do not repair, replace or remove any part of the
appliance unless specifically recommended in the
manuals. Improper installation, service or maintenance
can cause injury or property damage. Refer to this
manual for guidance. All other servicing should be done
by a qualified technician.
Remove all tape and packaging before using the
appliance. Destroy the packaging after unpacking the
appliance. Never allow children to play with packaging
material.
Hidden surfaces may have sharp edges. Use caution
when reaching behind or under appliance.
Improper installation can mean to lose the warranty.
Safety Codes and Standards
This appliance complies with one or more of the
following Standards:
UL 858, The Standard for the Safety of Household
▯
Electric Ranges
UL 507, The Standard for the Safety of Electric Fans
▯
CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators
▯
CAN/CSA-C22.2 No. 61-M89 Household Cooking
▯
Ranges
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
Electric Safety
WARNING
Before you plug in an electrical cord or turn on power
supply, make sure all controls are in the OFF position.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
The circuit breaker should have a contact separation of
at least 3 mm on all poles.
D A N V E S A
WARNING
RISK OF ELECTRICAL SHOCK OR FIRE
Frame grounded to neutral through a ground strap.
Grounding through the neutral conductor is prohibited for
new branch-circuit installations (1996 NEC), mobile
homes, and recreational vehicles, or in an area where
local codes prohibit grounding through the neutral
conductor.
For installations where grounding through the neutral
conductor is prohibited,
disconnect the link from the neutral,
a.
use grounding terminal or lead to ground unit,
b.
connect neutral terminal to lead branch circuit neutral
c.
in usual manner (when the appliance is to be
connected by means of a cord kit, use a UL listed 4-
conductor cord for this purpose).
Be sure your appliance is properly installed and
grounded by a qualified technician. Installation, electrical
connections and grounding must comply with all
applicable codes.
Before installing, turn power OFF at the service panel.
Lock service panel to prevent power from being turned
ON accidentally.
Installer – show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
Related Equipment Safety
The appliance is only guaranteed safe to use if installed
by a specialist in accordance with these installation
instructions. The installer is liable for any damage
resulting from incorrect installation.
Never modify or alter the construction of the appliance.
For example, do not remove leveling legs, panels, wire
covers or anti-tip brackets/screws.
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located
above the surface units should be avoided. If cabinet
storage is to be provided, the risk can be reduced by
installing a hood that projects horizontally a minimum of
5 inches (127 mm) beyond the bottom of the cabinet.
Verify that cabinets above the cooktop are a maximum of
13" (330 mm) deep.
Under the stovetop, no refrigerators, dishwashers, ovens
without ventilation or washing machines must be
installed.
Note: We strongly recommend the installation of a
ventilation system with this appliance.
E E S T H N S I O C T R U S T I N
3