Operation; 1 Chime; 2 Making Settings And Programming Switching Times; 2 1 Menu Item Chime On / Off - Monacor PA-1200C Notice De Montage Et D'utilisation

The four cores of the colours white, grey, blue,
and violet are not connected and have to be
insulated .
9) Close the basic unit with the housing cover .

5 Operation

Switch on the amplifier or the basic unit with the
mains switch . The display (1) of the timer briefly
indicates
MONACOR PA-1200C
version . Then the date (d) with the weekday (e)
[ = Monday, = Sunday], the time (a), and the
1 7
timer status (b) are indicated . If the timer is set into
operation for the first time, the date and the time
have to be updated (see chapter 5 .2 .5 "Menu item
SET DATE & TIME") .

5.1 Chime

It is possible to trigger a chime with the buttons
CHIME A (2), CHIME B (3), and CHIME C (4) .
CHIME A – one-sound chime
CHIME B – two-sound chime
CHIME C – three-sound chime
Adjust the desired volume with the volume control
LEVEL (6) .
Note: When these buttons are pressed, announcements
from the digital message insertion PA-1120DM and relays
are activated as well at the same time, provided that
the settings have been made according to chapter 5 .2 .6
"Menu item SET PUSH-BUTTON" .
5.2 Making settings and
programming switching times
To change to the programming mode, keep the
button PROG (5) pressed for 3 seconds until the
display shows:
MENU
ƊCHIME ON/OFF
In this mode, it is possible to program switching
times, to change or delete programmed switching
times, and to make basic settings (e . g . date, hour) .
All settings are permanently stored and are kept
even when the power supply is interrupted .
Important! When momentary pushbuttons are
connected to the connection PCB (fig . 3) for
remote control, they are connected in parallel to
the buttons CHIME (2 – 4) on the front panel; in
this case, do not press the momentary pushbuttons
during a programming procedure .
5.2.1 Menu item CHIME
With this menu item, all program steps can be
activated or deactivated .
1) After switching on the programming mode, the
and the software
2) Call up the submenu for the activation / deacti-
3) Define the setting with the button ENTER . Then
4) To exit the programming mode, select the menu
In the standard mode, the display indicates the
adjusted timer status (b) behind the time .
5.2.2 Menu item
To program a new switching time, go with the but-
ton UP (2) or DOWN (3) to the menu item
and use the button ENTER (4) to call up the first
submenu for starting the time .
A Setting the starting time
1) The display shows:
2) Confirm the setting with the button ENTER . The
3) Repeat the procedure for the minutes .
4) Press the button ENTER . The display shows:

Activating or deactivating the timer

item
ƊCHIME ON/OFF
menu item was selected in the meantime, go
to this menu item with the button UP (2) or
DOWN (3) .
vation with the button ENTER (4) . Activate the
timer with the button DOWN (display
deactivate it with the button UP (display
the display shows:
CHIME=ON
<PRESS ENTER>
To confirm, press the button ENTER again .
item with the button DOWN and confirm
ƊEXIT
with the button ENTER . The display shows time
and date again .
NEW SETTINGS
Programming new switching times
MENU
ƊNEW SETTINGS
SET TIME
00:00 [HOUR]
The hours can be set with the buttons UP and
DOWN . With the button kept pressed, the hours
advance or reverse .
display changes to:
SET TIME
xx:00 [MINUTE]
TIME=xx:xx
<PRESS ENTER>
Press the button ENTER again to confirm the
starting time . The submenu for the chime set-
ting appears .
ON / OFF
is selected . If another
ƊON
ƊOFF
CHIME=OFF
<PRESS ENTER>
or
) or
) .
13