Replace Dust Bag; Replace Disposal Bag; Replace Fine Particle Filter; Check Float - Renfert Vortex compact 3L Mode D'emploi

4.2 Replace Dust bag

• Turn off and unplug unit from the mains.
• Open holding clamps and remove top from ex-
tractor (Fig. 4).
• Carefully pull sleeve of dust bag off its connector.
• Push dust bag across sleeve opening.
• Dispose of dust bag according to local statutory
regulations.
• Clean dust retainer.
• Place dust bag in dust retainer and thoroughly push
holding sleeve onto bag connector (Fig. 5).
• Place top back on extractor and snap on holding
clamps (Fig. 6). Make sure clamps fit tightly.

4.3 Replace disposal bag

• Turn off and unplug unit from the mains.
• Open holding clamps and remove top from ex-
tractor (Fig. 4).
• Tap the cloth filter and remove carefully.
• Use string to close disposal bag.
• Carefully pull sleeve of disposal bag off its connec-
tor.
• Push slider across sleeve opening.
• Dispose of disposal bag according to local statutory
regulations.
• Place new disposal bag in dust retainer and thor-
oughly push holding sleeve onto bag connector
(Fig. 7).
• Fold top edge of disposal bag over edge of dust
retainer (Fig. 8).
• Insert the cloth filter into the dust retainer. Ensure
the position is correct (Fig. 9).
• The ends of the cloth filter should be draped over
the edge of the tank (Fig. 10).
• Replace the top of the extractor and close the re-
taining clamps (Fig. 6). Ensure the retaining clamps
are in the correct position (Fig. 11).
4.4 Replace fine particle filter
Never extract dust without putting in a
fineparticle filter!
• Turn off and unplug unit from the mains.
• Open holding clamps and remove top from
extractor (Fig. 4).
• Turn tightening disk anticlockwise and remove
(Fig. 15).
• Carefully remove fine particle filter (Fig. 16).
• Clean filter seal, check for damages and replace as
necessary.
• Put in new fine particle filter.
• Put on filter tightening disk and turn clockwise to
firmly lock in place (Fig. 17).
• Dispose of used fine particle filter according to local
statutory regulations.
• Place top back on extractor and snap on holding
clamps (Fig. 6). Make sure clamps fit tightly.
EN
4.5 Check float
• Switch the unit off and remove the plug from the
socket.
• Open clamps and remove the top part of the ex-
tractor (Fig. 4)
• Turn the spring washer in a clockwise direction and
remove (Fig. 15).
• Check the float is clean and able to move freely
(Fig. 18).

5. Spare Parts

You can find components subject to wear and the
spare parts on the spare part list in the internet at
www.renfert.com/p918.
The components excluded from the warranty (such
as consumables or parts subject to wear and tear)
are marked on the spare part list.
Serial number and date of manufacturing are shown
on the type plate of the unit.

6. Standard Delivery

1 Renfert Vortex compact 3L
1 Suction hose assembly, 3 m
1 Bag-type filter
1 Operating Instructions

7. Variants

No. 2924-5000 Vortex compact 3L, 230 V, 50 / 60 Hz
No. 2924-6000 Vortex compact 3L, 120 V, 60 Hz

8. Accessories

No. 2924-5003 Set of dust bags (5 pcs)
No. 2924-5005 Cloth filter
No. 2924-5002 Disposal bag (5 pcs)
No. 2924-5004 Fine particle filter 302000461
No. 2924-5006 90° angled connector
No. 900034305 Adapter for hose connector
No. 900034240 Suction hose
No. 900034314 Y-shaped adapter
No. 900034420 H- + Hepa Filter Vortex compact 3L
No. 2925-0000 Extractor clamp (w/o glass pane)
No. 2925-1000 Glass pane w/ holder
(for mouthpiece)
No. 2926-0000 Extraction distributor, including
4 sleeves (w/o hose)
No. 2921-0003 Set of sleeves, 2 pcs
No. 15-0823 Suction hose (by metre)
- 4 -