Group Power Control Setting For Manual And Ttl Fec - Hahnel ViperTTL Manuel D'utilisation

A B C
A B C
Speedlight
• Attach Speedlight to <hot shoe>
receiver. Using the slide switch
group A, B or C for this receiver. Turn on
TTL receiver which will give a green flashing light
to indicate power is on. Turn on the Speedlight. Press
<Test> button
15 on receiver to confirm Speedlight is
working
• Using the cable socket
connected to the Viper TTL receiver via a "Hähnel
Studio Light Cable" which is available as a separate
accessory
• Unlimited numbers of Speedlights / studio lights with
Viper TTL receivers can be allocated to one or different
groups
• For "Nikon" version, set the Nikon Speedlight to <i-TTL>
mode
Camera
• Mount the Viper TTL transmitter onto the hot-shoe of
the camera and lock it into place. Turn on the Viper
TTL transmitter and the camera. Press <Test>
button on transmitter to confirm Speedlight is triggered
• Press buttons A or B
setting of each group to <M> manual, <TTL> TTL or
<blank> OFF
• Take a test photograph now and the Viper TTL
transmitter will send a wireless signal to each
Speedlight connected to a Viper TTL receiver and to
each Modus 600RT. The Speedlights will be set to
the mode selected for each group on the Viper TTL
transmitter
5
The Viper TTL LCD will show the setting of each group
• A group is turned OFF if the LCD is not showing the group
• A group is in Manual mode when <M> is displayed next
to the group
• A group is in TTL mode when <TTL> is displayed next to
the group
A B
Each group or or
possible to use simultaneously different setting for each group
A
(e.g. Group may be in <M>, Group
C
Group turned OFF)
4
A B C
10 of the Viper TTL
16 select one of the
12 the Viper
14 a studio light can be
08
or C to change the MODE
C
is set independently and it is
B
in <TTL> and
Viper TTL - English
Group Power Control setting for
Manual and TTL FEC
From the Viper TTL transmitter you can adjust the power
level of each group which is in <M> mode
1. Press <SEL>
B and
2. Press one button
you want to adjust the power. Now only the selected
group icon
3. Turn the red <Adjust Dial>
the power level
4. The output power can be adjusted from 1/128 to 1/1 by
turning the red <Adjust Dial>
5. Press <SEL>
11
From the Viper TTL transmitter you can adjust the FEC
level of each group which is in <TTL> mode
1. Press <SEL>
B and
2. Press one button
group you want to adjust the FEC level. Now only the
selected group icon
3. Turn the red <Adjust Dial>
the FEC level
4. The icon <
compensation amount is changed. Turing the red
<Adjust Dial>
Turing the dial
5. Press <SEL>
• The power level of a studio light cannot be controlled
wireless by the Viper TTL. Adjust the level manually from
the studio light controls
• The setting of each group in the Viper TTL will remain even
if the Viper TTL is turned off or needs batteries exchanged
• Manual output power setting < -- >. In this power output
level the Viper TTL will not control the power level this can
be adjusted on the Speedlight. It is recommended to use
this setting for non compatible Speedlights which do not
allow power control via the Viper TTL wireless system
Simultaneous Group power
adjustment - FEC adjustment
From the Viper TTL transmitter you can easily adjust the
output power level and FEC setting for all groups
1. Press <SEL>
all power levels/FEC settings of groups A,B,C will flash
2. Turn <Adjust Dial>
power levels/FEC settings up or down to the new
desired value
3. Then press <SEL> button
Viper TTL - English
02 select button and all three icons
C will flash
A or B C
or to select which group
A or B or C will flash
03 up or down to adjust
03 up or down
02 again to save the new power level
02 select button and all three icons
C will flash
A or B or C to select which
A or B or C will flash
03 up or down to adjust
> will be shown when the flash exposure
03 up will increase the FEC to max +3.
03 down will reduce the FEC to min -3
02 again to save the new power level
02 button for more than 3 seconds and
03
to adjust simultaneously all
02 to save the setting
A
,
A
,
5