Attaching The Cover; Protective Clothing - stayer S90PE Instructions D'emploi

Intended Use
The machine is intended for making separating cuts and
cut-outs in wood, plastic, metal, ceramic plates and rubber
while resting firmly on the workpiece. It is suitable for
straight and curved cuts with mitre angles to 45°. The saw
blade recommendations are to be observed.
illustrated description
1. Handle
2. On/Off switch
3. Setting button I/0
4. Turning knob for stroke rate selection
5. Power cable with power plug
6. Vacuum connection adapter
7. Saw foot
8. Vacuum flow control
9. Pendular stroke setting 0/I/II/III
10. Guiding roller
11. Saw blade
12. Side grooves
13. Saw blade holder
14. Laser guide
15. Laser battery compartment
16. I/0 laser switch
Accessories
17. Large allen key
18. Small allen key
19. Parallel cut guide
20. Tightening screw of the parallel guide
21. Cover
22. Plastic guide
23 Tightening screw
24. Guideway opening
25. Underlying disc
26. Tightening screw
27. Plastic cover for saw foot
28. Angle scale
29. SDS lever insertion
30. Protection against contact.
Assembling the jigsaw
Mounting the cover
Danger of injury!
- Before performing any work on the electric power tool,
disconnect the power plug from the outlet.
- Put the cover (21) before connecting the jigsaw to the
power outlet.
Removing the cover
- Pull one side of the cover out of the groove (12), and
then pull the other side out in the same way.

Attaching the cover

- Push it in between the free space, in front of the saw
blade, between the sawfoot (7) and the case. While
pushing the cover in position, insert the right side of the
cover into the groove (12) on the right side of the jigsaw.
ENGLISH
23
• Place the other side of the cover on the left side groove
(12). Push the cover until it is completely locked in place.
Note: The cover (21) can only be used when cutting flat,
for angled cuttings the cover (21) must be removed. In
this case please use extreme caution when handling
the jigsaw.
Inserting/changing the saw blade ( ill. B/C)
- To replace the saw blade (11), use the small allen key
(18).
- Remove the cover (21).
- Loosen the screw (23) of the saw blade holder (13) until
the saw blade can easily be pulled out from the saw
blade holder (13).
- Push the new saw blade into the saw blade holder (13).
Position the saw blade teeth in the sawing direction!
Make sure that the back of the saw blade is in the middle
groove of the guiding roller (10).
- Tighten the screw (23) of the saw blade holder (13).
Make sure that the saw blade is always firmly attached
to the saw blade holder (13).
Inserting/changing the saw blade JS55BE (ill. B)
- To replace the saw blade (11), use the allen key (18).
- Place the cover against projections (21) in a comfortable
position to insert the allen key (18)
- Loosen the screws (23) for holding the saw blade until
the cutting saw can be easily removed from its bracket.
- Push the new saw blade into the saw blade holder (10).
Position the saw blade teeth in the sawing direction!
Make sure that the back of the saw blade is in the middle
groove of the guiding roller (10).
- Tighten the screw (23) of the saw blade holder. Make
sure that the saw blade is always firmly attached to the
saw blade holder.
Danger of injury!
- Disconnect the power plug (5) before inserting/changing
saw blade.
- Due to friction, the saw blade can become very hot
during operation! Wait a little while, until the saw blade
has cooled down. Danger of burns!
- The teeth of the saw blade are very sharp!
- Make sure that the saw blade is always firmly attached to
the saw blade holder.
- When storing the jigsaw remove the saw blade from the
saw blade holder.
Operation

Protective clothing

- If possible, wear designated gloves for protection from
splinters and shavings.
- While working, wear designated protective goggles.
Flying shavings can cause injury.
- Wear hearing protection for protection against continuous
noise in the work place.
- Wear a designated dust mask for protection against
airborne dust.
23