General Power Tool Safety Warnings; Illustrated Description; Attaching The Cover - stayer S90PE Instructions D'emploi

General Power Tool Safety Warnings

- Keep hands away from the sawing range. Do not
reach under the workpiece. Contact with the saw blade
can lead to injuries.
- Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
- Pay attention that the base plate rests securely on
the material while sawing. A jammed saw blade can
break or lead to kickback.
- When the cut is completed, switch off the machine
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the machine securely.
- Use only sharp, flawless saw blades. Bent or unsharp
saw blades can break or cause kickback.
- Do not brake the saw blade to a stop by applying
side pressure after switching off. The saw blade can be
damaged, break or cause kickback.
- Use suitable detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines can
lead to fire and electric shock. Damaging a gas line can
lead to explosion. Penetrating a water line causes property
damage or may cause an electric shock.
- Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and shock the operator.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
- Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn or
explode.
- Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
- Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
General Power Tool Safety Warnings
Read all
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
safety warnings and
ENGLISH
17
Intended Use
The machine is intended for making separating cuts and
cut-outs in wood, plastic, metal, ceramic plates and rubber
while resting firmly on the workpiece. It is suitable for
straight and curved cuts with mitre angles to 45°. The saw
blade recommendations are to be observed.

illustrated description

1. Handle
2. On/Off switch
3. Setting button I/0
4. Turning knob for stroke rate selection
5. Power cable with power plug
6. Vacuum connection adapter
7. Saw foot
8. Vacuum flow control
9. Pendular stroke setting 0/I/II/III
10. Guiding roller
11. Saw blade
12. Side grooves
13. Saw blade holder
14. Laser guide
15. Laser battery compartment
16. I/0 laser switch
Accessories
17. Large allen key
18. Small allen key
19. Parallel cut guide
20. Tightening screw of the parallel guide
21. Cover
22. Plastic guide
23 Tightening screw
24. Guideway opening
25. Underlying disc
26. Tightening screw
27. Plastic cover for saw foot
28. Angle scale
29. SDS lever insertion
30. Protection against contact.
Assembling the jigsaw
Mounting the cover
Danger of injury!
- Before performing any work on the electric power tool,
disconnect the power plug from the outlet.
- Put the cover (21) before connecting the jigsaw to the
power outlet.
all
Removing the cover
- Pull one side of the cover out of the groove (12), and
then pull the other side out in the same way.

Attaching the cover

- Push it in between the free space, in front of the saw
blade, between the sawfoot (7) and the case. While
pushing the cover in position, insert the right side of the
cover into the groove (12) on the right side of the jigsaw.
17