Switching On/Off - stayer S90PE Instructions D'emploi

Danger of accidents!
- Make sure that the On/Off switch (2) is not pressed down
or locked by the setting button (3). Connect the power
plug to a corresponding power outlet.
- Switch the jigsaw on only with an inserted saw blade (11).
- Use only flawless saw blades. Immediately replace blunt,
twisted, or cracked saw blades.
- Pay attention when working that the air vents are not
covered up or congested.
- After switching the power tool off, do not decelerate the
saw blade by pressing the blade sideways against a
foreign body (i.e. wood, metal etc).
- Danger of backlash! Only put the power tool away after
the saw blade comes to a complete standstill.

Switching On/Off

- Switching the jigsaw On.
Short-time operation:
Keep the On/Off switch pressed Jigsaw starts up Release
the On/Off switch Jigsaw stops.
Long-time operation:
Keep the On/Off switch (2) pressed and press the setting
button (3) (I ) Jigsaw runs in long-time operation.
Before the saw blade (11) comes in contact with the
workpiece, allow the saw blade to run until the full speed is
reached. Then guide the saw blade slowly along the
sawing line.
Danger of accident!
- Should the power tool fall out of your hand during
longterm operation, it will not be automatically switched
off. In this case, immediately pull out the power plug (5)
from the power outlet.
- Switching the jigsaw off:
Press the On/Off switch once. The setting button (3) will
automatically be released (0 ). Jigsaw stops
Pendular stroke setting
S110PE/S110PEK/JS80BPE
When set to the pendular stroke, there will be a forward and
backward movement in addition to the up and down movement
of the saw blade. Through this, the saw accelerates and the
saw blade will be protected from damage.
Set the switch 0 / I / II / III (9) to one of the following
positions:
ENGLISH
24
Tip: The best combination of stroke rate and pendular
stroke setting is dependent upon the workpiece. We
recommend to perform a test run on a piece of scrap
material. This way the most appropriate setting can be
found.
Setting the stroke rate
The stroke rate indicates the number of the up and down
movements per minute of the saw blade. The required
stroke rate depends on the work load and workpiece. On
one hand, an adequate working speed should be reached,
on the other, a clean cut should be achieved.
- Select the desired speed with the turning knob (4):
- To increase the speed turn the knob counterclockwise.
To decrease the speed turn the knob clockwise.
- With fine saw blades a higher stroke rate can be used;
rough saw blades require lower speed.
- After using the jigsaw for a longer period with a high
stroke rate, the power tool can heat up intensely - allow
the power tool to cool down for 3 minutes running idle at
maximum speed.
Straight cut ( ill. F)
When using the jigsaw to perform straight cuts, remember
to attach the cover (21), plastic guide (22) and the plastic
sawfoot cover (28). The use of the plastic guide (22) will
prevent the sawblade from swinging during the cut.
Angle cut
Setting the cutting angle (ill. D/F)
- The preset angle between the saw foot (7) and saw
blade (11) is 90°. You can adjust this angle on both
sides gradually to 15°/30°/45° using angle scale (28) as
reference.
Danger of accidents!
- Pull out the power plug (5) from power outlet before
setting the angle cut.
- The teeth of the saw blades are very sharp!
- Use the large allen key (17) to set the sawing angle.
- Loosen the tightening screw (26) with the allen key far
enough so that the saw foot (7) can be easily turned.
- For straight cuts (0°) the angle scale (28) should be set to 0°.
For angle cuts set the scale to value between 1° and 45°.
- Set the saw foot to the desired position 15°/30°/45° on
the angle scale (28).
- After the angle is set push the saw foot (7) down until is
locked in place.
- Retighten the tightening screw (26) with the large allen
key (17).
Dip sawing ( ill. E)
Only soft working materials, such as wood or plaster
cardboard, may be used for dip sawing! For dip sawing,
only use short saw blades and always set the sawing
angle to 0°.
- Place the peak of the saw blade (11) and the front parts
of the saw foot (7) on the workpiece.
- Switch the jigsaw on and allow the saw blade to run.
- Slowly reduce the angle of support of the saw foot in the
direction of the workpiece. The saw blade „dips" into the
area to be cut out. At this time, the power tool may not
be moved sideways.
24