stayer S90PE Instructions D'emploi page 22

General Power Tool Safety Warnings
- Keep hands away from the sawing range. Do not
reach under the workpiece. Contact with the saw blade
can lead to injuries.
- Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
- Pay attention that the base plate rests securely on
the material while sawing. A jammed saw blade can
break or lead to kickback.
- When the cut is completed, switch off the machine
and then pull the saw blade out of the cut only after it
has come to a standstill. In this manner you can avoid
kickback and can place down the machine securely.
- Use only sharp, flawless saw blades. Bent or unsharp
saw blades can break or cause kickback.
- Do not brake the saw blade to a stop by applying
side pressure after switching off. The saw blade can be
damaged, break or cause kickback.
- Use suitable detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines can
lead to fire and electric shock. Damaging a gas line can
lead to explosion. Penetrating a water line causes property
damage or may cause an electric shock.
- Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and shock the operator.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
- Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn or
explode.
- Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
- Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
Batteries use and care
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool.
ENGLISH
22
This measure alone protects the battery against
dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction
, until the tool can be inserted. Insert the tool. Firmly
tighten the collar of the keyless chuck 2 by hand in
rotation direction . This automatically locks the drill
chuck.
The locking is released again to remove the tool when
the collar is turned in the opposite direction.
General Power Tool Safety Warnings
Read
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
22
all safety warnings and all