Maintenance And Inspection - HIKOKI SP 18SB Mode D'emploi

English
(3) Cover the rubber pad with the wool bonnet.
Pull the string of the wool bonnet, let it connect
the rubber pad, and tie the string up. Then, tuck
the knot and the remainder of the string into the
wool bonnet. (See Fig. 2)
CAUTION:
Improper fitting of the wool bonnet may cause
vibration.
Confirm that the lock lever is disengaged by pushing
lock lever two or three times before switching the
polisher on.
2. Dismounting
To remove the wool bonnet, follow the above
precedures in reverse.
PRACTICAL POLISHER APPLICATION
1. Curved surface as well as plain one is treated for
finishing. It is recommended to hold the polisher
without pushing on the material, and make the best
of the weight of the machine alone. As the excessive
pressure on the polishing surface will not only bring
unsatisfactory result but also apply overload on the
motor.
2. Depending on the finishing degree of the surface,
use the polishing compound or wax. In order to
attain the maximum polishing effect, first polish the
surface with the fine sand paper using the sander,
than polish it with the polishing compound using
the wool bonnet, and than finish with wax. Apply
a small quantity of the compound and wax to the
surface, and polish with the wool bonnet.
3. Don't let the cord touch the wool bonnet during
its operation, for the rotating wool bonnet may
catch the cord and get caught it in.
4. Switching on the polisher
Pulling the trigger of switch and push the stopper,
it keeps the switched-on condition and it is
convenient for the continuous operation. When
switched off, the stopper can be disengaged by
means of pulling the trigger again.
5. Precaution after use
Do not lay the polisher down immediately after
using on a place where there are many shavings,
much dirt and dust until it has completely stopped
revolving.
CAUTION
When the polisher is not in use, the power source
should be disconnected.

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
2. Maintenance of the motor
The motor unit winding is the very "heart" of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
7
3. Inspecting the carbon brushes (Fig. 4)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brush with new ones having the same carbon brush
No. shown in the figure when they becomes worn
to or near the "wear limit". In addition, always keep
carbon brushes clean and ensure that they slide
freely within the brush holders.
4. Replacing carbon brushes
Disassemble the brush caps with a slotted-head
screwdriver. The carbon brushes can then be easily
removed.
5. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modification and inspection of HiKOKI Power
Tools must be carried out by a HiKOKI Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the HiKOKI Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATION
HiKOKI Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specific regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling
instruction, to a HiKOKI Authorized Service Center.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.